Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I'm trying to get LPCOMP working on Zephyr - I have used the vanilla NCS sample as a baseline and have set up the event handler and the init function.
The problem is that...
Hi,
I recently bought a couple of HolyIOT nRF52840 modules for a personal project (building a keyboard). I also got a JLink Edu Mini to flash/debug it. I am able to successfully...
Hello,
I've seen when ADV interval is near than 1 second, the sniffer cacth the same adv twice in diferent channels, but if the adv interval is near to 50 ms the sniffer...
Dear all,
I managed to implement custom firmware using Nordic proprietary protocol (both 1 and 2 MBPS) on nNRF-52840-DK. I would like to know if some spread spectrum tecnique...
A plain question : we are using the BLE stack with FreeRTOS based observers.
Is it possible to send to some observer an application defined event from some other FreeRTOS...
My project is a health thermometer using nRF52833. I am working nRF5 SDK 17.0.2 with GCC make complier.
I start with the ble_app_hts example and it is working fine. I try...
Hi,
I observed that in some cases SLM waking up from idle mode (at#xsleep=0) has CFUN reset to zero, even if I run AT+CFUN=1 before at#xsleep. Presumably that happens when...
My current implementation is based on light switch example and I am currently using nrf52832 kit with Mesh SDK v5.0.0. I have a mesh network setup with a client and two server...
Hello,
I am using nRF52833, nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 and SEGGER Embedded Studio for ARM 5.34.
I have imported some multiprotocol examples and trying...
I have an nRF 52832 running the SDK 15.2 with s132_nrf52_6.1.0_softdevice as peripheral and a Dell XPS 13 9350 laptop with the integrated bluetooth 4.1 module (Dell Wireless...
Hi,
can you please tell me in what cases I get this assertion?
SOFTDEVICE: ASSERTION FAILED, PCxxx: 0x12D7E
It seems to happen when a connection is active, timeslot...
HI All team Members !
Hope you all doing well ! . Yesterday , i have tested the two SDK's "ble_app_uart_c" as a BLE Beacons Scanner and "ble_app_beacon" as a BLE Beacon...
Hi,
I understand that the CoAP Client sample is configured for a public URL (californium.eclipseprojects.io) in the Kconfig file. I wanted to ask, how the KConfig file...
Hi,
I am trying to perform DFU over mesh network. I am following the steps as given in this .
I could achieve the steps from 1-6. But while running the command for Transferring...
