Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Referring to the Nordic message sequence chart in the following link:
https://infocenter.nordicsemi.com/index.jsp
(Software Development Kit -> Previous Versions of nRF5...
Hello!
I use SDK v17 and using the library and example code for the lsm9ds1 sensor.
github.com/.../nRF52-DK-and-LSM9DS1
'lsm9ds1_reg.c', 'lsm9ds1_reg.c' these two files...
Hello!
I am using ble adc scan mode example and successfully tested it with nrfconnect by sending my data from AIN3 . Now i want to send data of ble to raspberry pi bluetooth...
HI
Like to check on the usage of MQTT. We are connecting the nrf9160 to the network in eDRX.
During the interval, we may lose some message due to the lost of connection...
Hi.
I'm using ES.
RTT(Debug Terminal) on ES works fine. But sometimes I want to use J-link RTT viewer.
How can I turn off RTT on ES and then use J-link RTT viewer? ...
Hi,
as discussed in different issue on DevZone . We have discovered that send command freezes the program in the CoAP client sample. The Nordic employee Hakon has confirmed...
Hello,
This is related to a previous post , but now with new information and a more specific issue to resolve.
We have product in the field based on RF Digital's Simblee...
HI
I used nrf51822- EK board.
BLE HID MOUSE - SDK 8.0
`
How to send left button or right button data?
How to modify below method?
static void mouse_click_send...
Hi everyone,
I'm working on a custom bootloader for nrf52840-based board. The bootloader needs to support DFU from an external SPI Flash and also BLE. I was working on...
Hi everyone,
I am trying to use the nrfx_uarte driver. I did the following:
(a) setup driver
(b) setup the event handler
(c) finally tried to send some testing...
I noticed a lot of the early SDK's 11, 12, 13 examples that had the service changed characteristic enabled. I'm using SDK 16 and it seems that most examples don't enable the...
I'm building an LTE device that only needs the GPS, LTE, motion, and button.
I'm trying as the first step to disable all the sensors that are not needed so that I don't...
Hi Nordic When the BLE is connecting, the fs_event_handler hasn't any callback after doing nrf_fstorage_erase or nrf_fstorage_write.
It seems like the storage (nrf_fstorage_is_busy...
Hi,
I noticed that there were changes in some of the priorities in SDK config - these defines were changed from 7 to 6.
NRFX_CLOCK_CONFIG_IRQ_PRIORITY
NRFX_GPIOTE_CONFIG_IRQ_PRIORITY...
Hi Nordic Support,
I am currently developing an IoT application (battery powered, cellular device with a few sensors connected). I have spent the past year building the...
