Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Tried using the snippet with l2_e1 and got the same bus fault.
nrf Connect SDK v3.4.0
nRF Connect SDK Toolchain v3.4.0
[00:00:00.327,209] <err> os: ***** BUS FAULT ...
I am building a TWI slave with nRF52832.
I am attaching a part of twis_event_handler.
I can read even a 1-byte register value by executing i2c_read_register(SLAVE_ADDR...
Hi Team,
We are planning to use the nRF54LM20 + nRF21540 combination in our new design.
Currently, we are evaluating the band-edge performance on the highest BLE channel...
Hello,
we are seeing a reproducible issue with an external SPI NOR flash on our own custom hardware based on the Nordic nRF52833.
Short summary
The external flash works...
Hello,
My questions is regarding to the modem firmware.
I am planning to ship an IoT product and am questioning wether I should include an external memory for modem FOTA...
Hello, I'm stuck at the build step from teh IoT fundamentals course as when I try to build I get the next error:
It seems that the build needs two (samples/cellular/nrf91_crypto_partitions...
I happened to write some debug log code that broke my Bluetooth. I don't think it should be doing that. When I burrow into the logging, I don't see why this difference is...
We have switched over to the new device tree based partition scheme, and developed custom board files with not-secure variant and mcuboot for ota. OTA was tested using BLE...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic,
We are building a custom board using the nRF9151 LACA.
We see a back-powering issue between the GNSS antenna bias rail and VDD_GPIO.
Setup:
VDD_GPIO...
Hi:
I use ncs3.3.0 and nrf54l15dk.
PC BLE pairing nrf54l15dk failed log:
prj.conf
But with BT configuration, turning off ESB related content, it can be paired...
I have a nRF52832 custom board derived from the 52832DK board. All is working perfectly with the exception of the ADC converter. I am only using AIN0 which is on pin 0.02...
Hello,
I am working on a device based on nRF9160, SDK 2.8.0 and modem 1.3.7.
The devices uses nRFCloud CoAP to send messages. For the most part, it's working great....
