Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello, I was wondering if somebody has an explanation (or has seen the same problem) for the following event:
We have had 5 units with NRF9160-B0 in the field for testing...
Hello, On my nRF9160 custom device, I have enabled XPOFWARN to automatically switch off the modem in case the voltage gets too low. It's working fine. This case happens when...
Hello Engineer Greetings Of the Day We performed DFU over BLE with secondary slot in External flash that operates using SPI . I needed some clarification on the outcomes ...
We have a custom board with nrf5340 and we use SDK v2.5.3 for software development. Our BLE signal strength seems too weak with the default TX Power setting. So we would like...
Dear Team,
May I know how to install Nordic Edition of SEGGER Embedded Studio?
I did not see any executable file after downloading.
I ma onlz seeing the below files...
When building the Matter weather station sample, without any changes, I see many warnings regarding incorrect project configuration, such as conflicting options or missing...
I attached an external nRF52840 to the debug out port of the nRF 7002 DK (as seen here ), but cannot get a connection to the external uC.
I know the cable and uC work...
Hello Nordic community,
I’m working on a project that primarily uses GPIO for controlling locks, Bluetooth communication, and is powered by a battery. I’ve attached the...
Hello，
I am using a customized NRF52832 circuit board. During the Bluetooth connection test with a mobile phone, the connection suddenly disconnected, and then quickly reconnected...
We have an nRF9160 based product with firmware based on your AWS IoT Core example. Our devices are connected to the Telstra CAT-M1 Network in Australia (50501) using Modem...
Hello,
currently tampering around with "how to find out state of BLE TX FIFO", see e.g.
Next idea: is there any way to access BLE transmission/reception statistics? So...
Hi,
I am hit with a noticeable ram usage bump (~10%) when migrating from 2.5.0 to 2.7.0. Upon generating the ram_report, I notice that net_buf_data_hci_rx_pool has a huge...
The database that nRF Connect for Mobile pulls definitions from is significantly out of date (exact age depends on the category)
https://github.com/NordicSemiconductor/bluetooth...
