Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
looking at https://github.com/nrfconnect/sdk-nrf/tree/main/lib/location
specifically https://github.com/nrfconnect/sdk-nrf/blob/main/lib/location/cloud_service/cloud_service...
Hi, I am working on a project using the nRF52832 and the nRF5 SDK 17.1.0. We have a sensor with non linear behaviour and in our attempt to linearize it we found an article...
Hi,
I encountered a very strange issue. I need to control a device using GPIO. What I use is p0.22/p0.02/p0.03/p1.11/p0.31/p0.30. I modify the app.overlay file and check...
I'm running the SDK 17 radio test example on two custom board using nRF52833. My goal is to do a range measurement under ble_1Mbit mode.
My parameter as follows:
After...
Hi，
I am following the nRF Connect SDK Fundamentals course of Lesson 1 – nRF Connect SDK Introduction of Exercise 1 to install NCS development environment,when I executed...
When I tried to use PPK II to measure the alarm current of a smoke alarm product, I found that its test results were very different from those of the power analyzer. I didn...
Hi, I have a question regarding the nRF power management APIs. I'm trying to implement power management in my code, and I found that the pm_device_action_run() API can be...
Errata 36 for the nRF9161 (and the same problem exists on the nRF9151) disables the access port in SYSTEM ON IDLE, which is the default low power state for nRF9120 devices...
Hi,
My nrf9160-DK version is PCA10090, 1.1.3, 2023.31
I am trying to test the esim, but the firmware tells me no simcard found. After doublechecking the esim soldering...
Hello,
On T-Mobile's website [1] there are some documents relating to their certification requirements [2]. In their FAQ they state that they have minimum band requirements...
Hello, we are planning to evaluate several type of AoA algorithm, and we have ISP1907-AOA-DK kit from Insight-SiP Is there any guideline you know to get IQ data from each...
Hello, Im in the middle of a custom board bringup and I am attempting to get Bluetooth GATT server working. I have tested the bluetooth code using the nrf5340dk board files...
Hi,
I'm using nrf5340 audio dk board. I configured UART0 with the help of nrf connect fundamental course - Link and I started transmitting the data in UART. But after sometime...
Dear team,
I am trying to build my CPP project with Nordic Zephyr SDK. I am using following commands:
west build --build-dir nrf_build -b nrf52840dk_nrf52840 sample -DZEPHYR_TOOLCHAIN_VARIANT...
