In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hello, I.m using SDK 2.6.1 with VSCode.
I created a new application based on the sample /nrf/samples/net/mqtt configured for nRF9161_ns which is listed as a compatible board...
Hi,
When I define my nrf52840 pin 0.19 as input put, and there is no connection to any sensor.
Then I use gpio_pin_get_dt() to get pin 0.19 status, the status is high...
I downloaded the nRF Connect SDK v2.7.0 and read the Release Notes. I installed the v2024.7.18 (pre-release) version of the nRF Connect for VS Code. As a first step, I created...
Greetings
I am trying to configure the nrf5340dk to use the i2c0 bus. I believe i2c1 is already configured, but for learning purposes, I want to figure out how to do this...
Hi,
When I DFU upgraded the bootloader of my firmware, I found that during the upgrade process, when ret_val = bl_activate() was executed, the pin would be pulled low. ...
The product page for the Thingy53 only shows hardware files for the v0.8.0 board revision, not the 1.0.0 or v1.1.0 board revisions.
https://www.nordicsemi.com/Products/Development...
HI all!
So I'm trying to use and modify parts of the Asset Tracker v2 application for my own project and when I created a new application with the pre-existing sample on...
Hello all,
I am trying to write some code to read the sensor values from two VL53L0X tof sensors, but I'm having some trouble.
My current code:
My devicetree:
...
I am using the cloud client example and connect to the nRF Cloud. I receive message fine on an interval and when I press the button.
I do not get any notification in my...
Hi all,
I am hoping to eventually integrate the crashlog functionality, but prior to this, I wanted to test the basic functionality with the flashlog. I have looked through...
Hi,
I'm currently working on getting LTE to work on our custom card, featuring an nRF9161 and an MFF2 eSIM (without PIN), but I can't seem to initialize our eSIM. I have...
Hi,
I know this issue has been addressed in other posts but none of the solutions tested worked for me. I tried the solution of this post : Intellisense stops working when...
hw: nRF9160-DK, v1.1.0
Using the McuBoot-Loader of NCS 2.5.1 and the NCS 2.6.1 zephyr dfu module seems to be not longer aligned with it.
A app using NCS 2.5.1 zephyr's...
We are developing Matter/Thread based Smart Lock product. One of the product requirements is that the product should be able to connect to a BLE mobile APP at all times i...
