Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
As in topic I'am concerned about the impedance of SWD interface drivers.
I'am building and SWD interface multiplexer that will be used with 48 devices using J-Link Pro debugger...
Hi team,
I recently purchased some nRF54LM20A units and I am currently working on interfacing them with a W5500 Ethernet module over SPI. However, I am facing difficulties...
Hello, I am trying to configure the NRF9151-DK, but when opening Quickstart app it cannot verify the board. Here's the log. I've been working with exact same boards, also...
I just programmed 2 Boards.
One Peripheral advertising with 1m Phy and other peripheral with s8 codded phy.
Using NRF connect app and wire sharc I made sure that I really...
I had TWO DKs as described in the title randomly fail on me in the same way, months apart. Additionally, I had an earlier rev DK, 2.1.0 (NRF5340 is NOT the IMCU on this version...
Hi,
I'm working on a project with the nRF52840 using nRF5 SDK v15.3.0 and have been working on enabling dual-bank DFU in the bootloader. During this process I made several...
Dear Nordic
There are two questions. Thanks
Q1. Did you have temperature test report of nRF54LM20A (with NFC functionality)?
Q2. We want to implement FIDO (Fast Identity...
Hi,
I am new to Nordic environment.
I have a project build on nrf5340_cpuapp_ns. I want to enable logs on both non-secure and secure image.
Currently I am only seeing...
Description ===========
I am trying to use the native HTTP/HTTPS AT commands of the nRF93M1 to download a firmware image for an external host MCU.
Hardware and software...
Hello,
I ma gathering some data from nRFCloud API, and I noticed a small issue with the pageNextToken. I noticed this on https://api-docs.nrfcloud.com/#tag/FOTA-Job-Executions...
Hi
In my project I have set CONFIG_BT_AUTO_PHY_UPDATE=n in prj.conf. I am using NRF connect sdk 3.4.0
I have configured both central and peripheral to s8 advertising and...
I'm trying to capture a ble connection with nrfutil. What I've done:
- installed nrfutil on my arch based linux machine
- install ble-sniffer
- setup the nRF52840 Dongle...
Hello Nordic team,
I am working with an nRF54L15dk and have an issue using P0.01 as a GPIO input.
P0.03 works correctly with the same GPIO configuration, but P0.01 does...
This is a follow up to case 356908 which was closed due to no resources available. --- We need to shutdown the modem or we end up locking it in the reset-protection state...
