I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Here is a warning I get linking an application that uses nRF DM library 5/14] Linking C static library app\libapp.a [6/14] Linking C executable zephyr\zephyr_pre0.elf c:/toolchains...
Hi,
Can any one list what are the reasons for sd_ble_gap_connect returns NRF_ERROR_DATA_SIZE?
In ble_gap.h NRF_ERROR_DATA_SIZE error code doesn't exist for sd_ble_gap_connect...
Hello,
We have already product with BLE 4 and now we are moving to BLE5. As per the example code we have updated our code to BLE 5 but we are not seeing advertisement...
Purpose: to develop a central device using nRF5340 and to enable both BLE Mesh and AoA features.
Questions:
1. nRF5 SDK supports nRF51 and nRF52 series but not for nRF5340...
Hello,
We were middle way during the development when we found out that we had a higher packet loss than what is acceptable.
So we start to analyze this issue.
Scenario...
Hi,
I reviewed the PCA10121 schematic for using SPI4 pins to connect to Semtech SX1262. Since SPI4 bus also connected to SD card and DSP. I checked to see if SPI0..3 pins...
In my application, we regularly transmit a stream of notifications from a Peripheral Server to a Central Client. The general strategy for this is to enqueue a packet, and...
Hello in my app I based it on the BLE UART example and have it pretty much up and running but I need to be able to send multiple messages from the Central to the Peripheral...
I am tring to update the DK bootloader by entering the maintenance mode by pressing the reset button while plugging in the DK, but the board does not show on my PC
any help...
Hi,
I do have Zephyr's logging configured using RTT for debugging messages and in general this works.
Sadly when reflashing (via SWD) the RTT stops working and I have...
Hello,
We are using nrf52832 and SDK15.3 in our product, which sends about 7.4K bytes data every second to an Android phone.
4 ble devices are connected to the phone and...
Hi experts,
I habe a following issue. First I have tried to use nrfx_twi driver. There was any data send over I2C... So I have written own driver using the Datasheet and...
We are trying to send a large message via a BLE characteristic and to do that we have broken up the message payload into smaller fragments and calling bt_gatt_notify() repeatedly...
hi：
I use ble_app_uart routine, test the receiving rate, use the mobile phone to send data, 52832 receive the fastest can only be 10KB.
In addition, when the interval...
