I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hello,
I am successfully able to open and close adapter for nRF52840 using pc-ble-driver-py using python3.6.0 on my host armv7 Linux board.
But doing same inside the docker...
Hi,
We are developing BLE firmware that will allow BLE pairing without bonding (but with PIN/Passkey that is entered from the phone). However, when I try this with nRFconnect...
Hello Nordic Support.
I would like to build and use a Sniffer using a PC (Windows 10), nRF52DK, and nRFConnect for desktop.
Please teach me about the following.
nRFSniffer...
Hi, I can successfully build the Matter light bulb example in nRF Connect SDK 1.9.1 but I fail to do the same in v1.9.99-dev1.
What did you change?
Here the error:
west...
Dear DevZone support team
I'm facing the following problem: My application uses the Zephyr's BLE stack and basically does not much beside parsing JSON-messages received...
Hi,
I tried to implement PPI for a very timing sensitive application. The sample PPI_trace uses the RTC but it is too slow for my application so I'd want ot use timer0...
Hello,
We would like to use BLE to transmit a lossy data stream at high data rate. Looks like Isochronous channel is the best choice. How's the Isochronous channel is...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Hi,
I work on an AOA projet and i have a problem.
I have already made a transmitter (with an nRF52833) and a receiver (also nRF52833) and i can see the CTE send by my...
I need to add a custom BLE service with over 20 custom characteristics. During the gap nitialization step, I set the BLE security mode and security level like this:
sec_mode...
Hi ,
Am following the below link https://devzone.nordicsemi.com/f/nordic-q-a/83402/ncs1-8-0-52840-mcuboot-spi-external-flash-can-t-build-pass ,
am able to build it for...
hello,
i am using nrf52832 with accelarometer i want to put my board in shutdown for current consumption for that i am giving this command sd_power_system_off(); whenever...
I need to be able to change the device name the SoftDevice uses AFTER the soft device is up and running. To change the device name, To do this I use
errorCode = sd_ble_gap_device_name_set...
Hi,
I currently have a macro in the nRF Connect Mobile app (Android) that displays RSSI every time I receive a temperature signal. I am saving the logged temperature and...
It seems that not all UICR registers are erased on this nRF52840 chip
nrfjprog -f nrf52 --recover
Just make sure one more time:
nrfjprog -f nrf52 --eraseuicr
nrfjprog...
