Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi Nordic Team,
I noticed a potential issue while migrating from SLM v1.4.0 to v1.9.0. In addition to the inversion of the <state> representation in #XHTTPCRSP introduced...
I have developed a Zigbee application using the nrf52840 DK board + nRF Connect + Zephyr and it is working. Now I am trying to move that app over to the nrf52840 dongle. It...
Hi, I am using nRF52832 development board and I have a motor driver. Motor driver has external power supply, I am just using nRF52832 to set directions which consumes low...
Hello, I am trying to use the dfu library to update the nrf52840 with a firmware stored in a littlefs file in an external qspi flash. I can successfully read the entire firmware...
Dear Nordic team,
it is very important for the RF and the HW engineers to be able to know the current transmit power of the modem. That will help us evaluate the network...
Hi
I'm looking for an example implementaion code on the nRF52840 without an operating system. Is there some example or application note?
I connected the SPI and all IO...
Hi,
I updated to VS Code V1.65 today and had some strange behavior with the NRF connect extension for VS Code.
After updating, clicking any "Action" in the sidebar (e...
I have already implemented DFU update in our one product. Which have fast USB interface and fast "lag-less" UART interface to nRF chip which is used as our bluetooth central...
I am using a code based on nrf52-ble-app-uart-c-multilink ( https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink )
If the central is working and the peripherals...
Board: NRF52833 (PCA10100)
SDK version: 17.0.2
Softdevice: S122
I am trying to perform USB DFU for my application. As I am using nrf52833 board, there is no available...
Hi ,
SDK 17.1.0
SD132
SoC - nrf52832
I am following the below given link to create custom service.
https://github.com/bjornspockeli/custom_ble_service_example...
We plan to use it with the Converter mode enabled for low current consumption.
However, if PIN is always set to Hi in order to use the Converter mode, about 300μA will...
After a lot of thought about the issues with TCP under EDRX or PSM , I have a feature request.
I would like if the application layer could know when a TCP socket was sitting...
