The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi,
I am currently setting up an MQTT client via the MQTT publisher sample on zephyr.
My mqtt client is a NRF5340 and it is connected via ethernet with my pc and also...
Hello support
I have modified the cli examples and run into "undefined reference to `nrf_cli_uart_transport_api'" linker error.
The error message is
Compiling file:...
Here's my setup:
1. RPI4+nRF52840 dongle as OT border router
2. nRF5340DK running CoAP client example application
3. Wireshark running on Mac OS, with nRF52840 dongle...
Hello!
I'm trying to develop a mesh network and I've been building on top of sensor example, which has been very useful since I'm reading a few sensors. However I want to...
I am trying to generate ECC key pairs using MbedTLS on Connect SDK.
I found this code block on stackoverflow and validated from mbedtls/programs.
"mbedtls_ctr_drbg_seed...
I was trying to evluate the Periperhral ISO server, however with a NR52dk, but it returns ENOTSUP.
Bluetooth initialized Unable to register ISO server (err -134) [00...
Hi all
I am developing a proprietary radio protocol application using the nRF52805. I am not using a softdevice. Instead, this is all done by accessing the radio registers...
I have seen this question answered for the old Nordic SDK but have not been able to find a solution in Zephyr & NCS. I'm following this post on how to develop a custom BLE...
Hello,
i am using nrf52832 dev kit want to send the nrf calendar parameter through nrf connect app and send through app successfully by taking uint8_t datatype .I have receive...
Hello.
I am trying to write code to read data using saadc and write the sampled data in a micro SD card using fatfs.
I started from the fatfs example and initialized...
I'm attempting to use pc-ble-driver-py on Windows with an NRF52 DK (PCA10040) and running into the error shown below. Using the Heart Rate Collector example, the COM port...
Hi,
I'm using the ble nus uart for my application and I noticed that I was drawing too much current so I went back to the example from the SDK 17.0.2_d674dde which I haven...
I have followed the Azure IoT Hub — nRF Connect SDK 1.6.99 documentation (nordicsemi.com) and was able to comminicate with Azure IoT hub.I have created rootCA and device certificates...
This is my problem description, hope someone can help me. 1. The watch product shipped in mass production is found to be disconnected when using the mobile phone OPPO-k7x...
HI,
i have enabled CONFIG_BT_SETTINGS_CCC_STORE_ON_WRITE=y
so after power cycle the device automatically connects with iphone and the service also works fine
after this...
