Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I wanna use nRF52820 to make some application development.I wanna a sing-board development kit for nRF52820 ,and nRF52833DK supports development on the nRF52820 SoC and nRF52833...
Hi Everyone This is my first time designing a PCB with the NRF51822. I have designed it using an 2450AT18B100E Antenna and a BAL-NRF02D3 balun. Below is my schematic:
...
There are discussions on WLCSP light sensitivity for nRF5 product, which affects RF, clock accuracy, and low power current draw etc. what about the nPM1100 which clock accuracy...
Is my understanding correct that with VDD supplied and ENABLE = high, having VDD_GPIO floating (i.e. disconnected from a regulated 3.3 V supply) is a valid state? We intend...
hello Nordic
i am working with nrf52840 sdk16.0 s140
i wish to read the UICR register value like this :
but i get this compilation error
since it is a define...
Hello, I'm working the nrfx saadc legacy driver, and despite changing whether I measure Vdd(on the dk) or GND, the saadc output(p_event->data.done.p_buffer[0]) oscillates...
SDK14.0+NRF52832（PCA10040 demo board）:
I want to add static passkey to avoid MITM attack， I write code as following, but when I use the mobile app ‘nRF Connect’ to connect...
Dear community,
I need to operate a BM833A as I2C slave and to do so, I performed the following steps:
I modfied my sdk_config.h and set TWIS_ENABLED and NRFX_TWIS_ENABLED...
Hi,
I used nRF Connect for power profiler and programmer for hundreds of times.
But since today, it just keeps on showing white screen.
I tried "Ctrl + R" as well as...
Hi Team,
We are using the NRF52840 SOC for our development purpose and in our application we are planning to port the RTOS.
Could you please suggest us which RTOS is...
HI,
I am using the central_hids project in NCS V1.5.1 on NRF52840 , and now i want to add USB hid into the project, how can i do it?
I have try to do it in nrf_desktop...
Hello,
I've been trying to learn to develop an app based on ZigBee, it's the first time i'm working with nRF hardware and the only things i've done so far was to run some...
Hi,
I am currently trying to embed the ATT_MTU throughput example on two nRF52840 dongles. The main issue I am facing is that after I compile and program the hex files onto...
Hi everyone,
I am working with the nrf52832 Dk boards,
So my question is I want to connect sensors to two nrf52832 boards and want to get their data on a single Android...
