I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
Hi,
I started coding form ble_app_uart, and whenever I set a breakpoint and it's caught, then I press Resume (eclipse), the code falls on NRF_BREAKPOINT_COND in app_error_fault_handler...
Hi
My English is not very good, but I encountered a problem that could not be solved. Please forgive me if there is any improper expression in grammar.
When SPI sending...
1.Development board used is nrf9160DK，sim car is nb-lot,set's network mode is nb mode，Turn off all peripherals
2.set eDRX mode,eDRX is 655.36s,pwt is 2.56s ,After the device...
I am using the GPIOTE driver to attach interrupts to a pin in a very timing critical environment (using sensors like this ).
To me, it seems like there is quite the significant...
In the v16.0.0 SDK the settings struct size is 904 bytes, but in the nrfutil it's 803 (screenshots attached). I figured the settings in python don't include peer_data(64bytes...
I was in the process of integrating a NAND flash to my project. - MX35LFxGE4AB
Initially, I thought it would be good idea to use QSPI, but it seems to only support NOR flash...
Hi
Im struggling to use the ble_app_template_cpp within SDKv16. I am using the nrf52840 DK (PCA10056) and want to us the S140 SoftDevice. The example isn't built for either...
Hello everyone:
The problem is still not resolved
Test broad is PCA10056
Test code was modified by \SDK17.0\examples\peripheral\usbd_msc\pca10056\blank\ses
Try to...
I am using a thingy52 device and in that, added code of advertising and scanning from the sdk 16. Advertising is run successfully. But getting packet loss issue. So, I am...
Hi
Im developing an application that will wake up on RTC every 15 minutes. My issue is that when using idle_state_handle, which in turn calls sd_ble_app_wait, the RTC...
Hi,
Trying to figure out the current requirement on GPIO input, can you point me in the correct direction in how to figure out how much input current the GPIO on nrf9160...
Hi,
we are planning to add a 256 MByte NAND flash to our sensor project. I saw the example for NOR flash on the PCA10056 which is working fine. But due to costs we want...
Hi,I am using the nRF52840 development board, S140 and SDK16.0, I have some questions about data transmission on the UART.
I am trying to make a central device that is similar...
Hi,
I am working on a custom nrf52840 board and am having trouble connecting to the usb interface on the chip. After testing with the dev kit, the adafruit bootloader...
I trying to establish communications with a (non Nordic) beaconed 802.15.4 coordinator.
I've used some code from the wireless_uart_raw example but did not use the FSM. ...
