Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I have a customer requesting any version above 0.8.5 for part number nRF9160-DK.
Can you tell me what date codes would have the requested versions?
thanks,
Russ
QB79869...
I'm looking for a low energy communication method for a wireless PIR motion sensing device. The system will be battery powered so RX current draw is particularly important...
We are revising a design using the NRF9E5, we are experiencing problems with the third harmonic when configured for 915MHz band, the higher we go up the band the worse the...
I am looking to build a custom board using nrf52840 and want both UART and flashing capabilty on the custom board. I have a NRF52840dk that I will use to program the custom...
I want to increase the pull-up resistor value to educe the current consumption.
but, I am afraid that the GPIO input will not be recognized as High.
I want to know the...
Hi,
I can't find this information anywhere in the AT command manual or datasheet. What is the accuracy for " AT%XTEMP?" and "AT%XRFTEST=10,1,0"?
Kind regards,
Thoma...
Hello,
I'm trying to generate project to realise new user-cases with wireless mesh networks.
I did a demo with the Thingy52 at flower greenhouses
They are very interested...
HI! I've done the basic Blinky and UART examples, and now have to move on to programming something on my own. ( I have to send EEG signals from one BLE board to another/notebook...
hai ,
i tried nrf52840 ota over BLE from third party (ESP32).
As per the DFU protocol implemented logics and upto init packet (.dat file) getting expected response from...
Hi, I'm looking to use P15 (Shield Debug out connector) on nRF9160-DK. Description here https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk%2FUG%2Fnrf91_DK%2Fhw_debug_out...
Hi I used the light ctl/lc example project and connected to it with my iphone app which uses nordic sdk. I made a slider which sends messages quite often to the mesh device...
We are presently using Raspberry Pi 3 Model B to observe BLE packets coming from sensors that have NRF52.
We are also able to do DFU OTA using the Nordic NRF52840 USB dongle...
Hi,
I am working on a design of very low power sensor, based on nRF52833. Most of the time my device spends advertising only, with sensor data transmitted within advertising...
Hi,
i want to devolep a keyboard by nrf52840,now the problem is some funcation the usb examle have not,so i want to konw how can i add the
1.consumer control？
2.system...
Full error report:
<info> app: Connected <error> peer_manager_sm: Could not perform security procedure. smd_params_reply() or smd_link_secure() returned NRF_ERROR_INVALID_ADDR...
