I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Dears:
I test the uart dfu by examples\dfu\secure_bootloader\pca10056_uart
After I enter command like below：
nrfutil dfu serial -pkg Sena_app_uart_s140.zip -p COM5 ...
My project is Obj-C , and “ pod 'iOSDFULibrary' ” in my Podfile.
It worked fine until I upgraded Xcode to 10.2. There are some errors(about 100) occurred during project...
Hi all
I am doing multiprotocal from sdk15.3 and I am trying to add nrf_gzp.c, nrf_gzp_host.c, and nrf_gzp_host_nrf5x.c in to the project
after compile successfully and...
I was wondering, is it possible to suspend/resume flash operation in nRF52840 (internal flash)? Like flash erase suspend, and also flash write suspend/resume?
Thank you...
Hi,
Might be a silly question,
but is there a gattc equivalent of the "BLE_GATTS_EVT_HVN_TX_COMPLETE", ie a similar/equivalent event that gets generated when a central...
Hey, I am working on the proximity application on nrf51 DK. How can I get the bsp_event_handler to get triggered on a button multi press (such as pressing button 1 twice rapidly...
Hi,
Do you have support for mobility in Cat-M on your nRF9160? This is usually done in RRC connected, but i'm wondering if you are able to support it in eDRX as well?...
Hello;
We are developing a project. And there must be three features in our project.
1) Should scan and transmit beacon at the sametime
2) Chip should read and write...
How can i read advertisement and not connect? I would like to do some checks on the advertising data within BLE event BLE_GAP_EVT_ADV_REPORT and then decide if i want to manually...
I am trying to transmit a modulated carrier with a high duty cycle but it does not work
the same command works with the default duty setting (50%).
The cli freezes when...
VUSB current consumption of the NRF52840: We have a setup where the 5V supply to this pin has very limited current capability.
What is the maximum current which can go into...
The Problem: HardFault within sd_softdevice_enable. With HardFault breakpoint enabled, the debugger halts at address 0x8C8. With this breakpoint disabled, breakpoints after...
I having trouble setting power level above +4 dbm in my app based on the example "ble_app_beacon" using the PCA10059 nRF52840 dongle. I have updated the main.c with the following...
Hi, i'm designing a device which is based on nrf52832 chip and i need to add two IC on my board, the first one is the MAX8856 to charge the battery of my device and the second...
I want to execute timer interrupt at a certain interval, like 1sec or 5 sec.
I measured an actual interval of voltage change with oscilloscope, but the actual interval is...
