Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Is it possible to use the TWIM and TWIS at the same time with 2 different I2C buses with openthread.
I tried this with THREAD SDK 1.1 and had link problems because of the...
Hi, I'm trying to setup attribute reporting on zigbee HA, the device role is ZB_ZCL_CLUSTER_SERVER_ROLE, I want to configure reporting for cluster 0x0006, so each time I flip...
SDK v14.0, SD132 v5.0.0
We're creating and starting app_timer instances before we enable SoftDevice via nrf_sdh_enable_request(). It seems to work, but I remember that...
Hello,
Is Bluetooth 5, capable to communicate with BLE devices as well as classical BT devices? I think this dual capability is called smart ready.
We are planning to...
Hi,
I can program our old Nrf24LE1 boards with Nrfgo Studio, but when I tried using Nrfgocli command it fails to connect to
the board. My motherboard is set to number...
I noticed that CMSIS Configuration wizard expects values in HEX and converts them into decimal in the sdk_config.h file.
e.g. for SEGGER_RTT_CONFIG_BUFFER_SIZE_UP. I entered...
Hello there, I am using nrf52840 The mark is: N52840 QIAAC0, SDK: nRF5_SDK_15.0.0_a53641a, SD: nRF5_SDK_15.0.0_a53641a, I used the BLE ANCS routine and encountered this problem...
Hello,
We have a custom board based on nRF52832. The problem is that when trying to run basic example Blinky (examples\ble_peripheral\ble_app_blinky\pca10040\s132\arm5_no_packs...
Timer interrupt does not work well. In the code below, LED doesn't turn off and "interrupt!" message is not received. I really appreciate it if you give me any advice.
Hi Everyone,
I want to make a program code to establish the connection between MCU(nrf52832 chip) and accelerometer.
What are the conditions required? and i need some...
I'm using nRF52840 with SDK 15.2, and SD backend for Flash storage. I try to implement a verifiedWrite() method to write to flash. And it work most of the time, but fail sometimes...
Hi,
Is it possible to find comparison on the power consumption when running the internal DC/DC converter at 1.8V and 3.3V?
I have an external SD-card that needs a lot...
In the documentation for the s140_nrf52_6.0.0 I find the following statement: "The PPI channels and groups that are reserved by the SoftDevice when enabled are defined in...
MCU: nrf52840
SDK: V 15.2.0 porting with nRF-IEEE-802.15.4-radio-driver
problem:
ble_nus_data_send function sometimes returns BLE_ERROR_GATTS_SYS_ATTR_MISSING error...
Hi,
I am currently updating a firmware from SDK 12.1 to SDK 15.3 on a custom board using a nRF52832. Application itself has been upgraded and works well with Soft Device...
