Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello.
I want to integrate UART and SPI ,I am using SDK15.2. The problem here is i am not able to add app_uart.h to main.c(spi).
My question here is how to add it to main...
My working platform is nRF52-DK, and I want to execute DFU firmware upgrade
1. How to create a Bootloader Image? Which Source-Code of SDK_15_2 is used to build the bootloader...
The RTC documentation states that the LFCLK source needs to be explicitly started by the software.
Is this step necessary when using the SoftDevice? As far as I know, the...
I'm not sure about how does the ble_app_att_mtu_throuthput example works exactly, i supose the throughput test runs as follows:
1 tester defines a service 'populated' with...
Dear all ,
Working with nRF52832 (currently without SoftDevice), and there some issues regarding the project current consumption that we need to understand:
1) In the...
Hi,
I am having a trouble trying to make a custom service from SDK 15.0 ble peripheral template example. I have followed the tutorial from : https://devzone.nordicsemi.com...
Hi i'm a newbie, Got Thingy:52 (Keil and J-link) and want to develop HOGP keyboard application. Where can I find Tutorial or example ?
Is there a step by step guide on how...
Hello everyone, I'm using nRF52 kit which has got only one UART module, i'm also using the log driver(which uses UART, typing stuff into a virtual terminal using NRF_LOG_INFO...
hello everyone, I need a low power product, so I am using nrf52840. There is a problem now, When I add "app_timer_init()"(I never change the code in this method) in my code...
Hi,
I'm currently experimenting with both the nRF52840 dongle and preview development kit and my question is the following :
Using a generic LTE IoT gateway with a linux...
This isn't a question more of an FYI for those who come after me...
I just spent the past hour (at least) trying to figure out why my code was producing an error on a call...
I want to compare some values of RSSI that I have obtained in a test that I have made with its corresponding theoretical value and to calculate this theoretical value I will...
I am working with the ble_app_uart example in SDK 12.3.0 for the pca10028 board, and want to add a second tx characteristic (the one which receives from the nRF Connect app...
In the blog article Bluetooth 5.1 Puts Bluetooth In Its Place this week:
At the locator hub, an antenna array needs to be designed and multiplexed to the Bluetooth SoC...
