Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
hello ,
can anyone guide how to add custom service and charactericteristic and receive data from nrf connect app using handler
i am using
board :PCA10040
nRF52DK ...
Hello guys!
We have a new project were will have to use dfu ota for a custom made application on a nrf51 beacon. Since the beacons use legacy dfu we want a way around...
Hello! I am trying to advertise two 16-bit uuid's and a 128-bit uuid. I set up advertising_init as such:
I declared the following structures:
where "SENS_UUID_SERVICE...
I am using Fanstel BT832 module based on nRF52832. I am using ' nRF5_SDK_14.2.0_17b948a ' with ' s132_nrf52_5.1.0_softdevice.hex '.
I am using this module as the BLE peripheral...
Hey Dear Nordic Devzone,
Here I am again, it has been a long time. Before I was working with the nRF52840 and Segger Embedded Studio. But as of now the company I am working...
i have programmed a arduino to send data(int value) on tx ,rx pin .How shoul i set up the nrf52 (the pin no of rxd and txd on nrf are p0.6 and p0.8).Which example should i...
Hi,
I'm looking into the reliability of the BLE connection from one nrf52 to another nrf52. I'm looking to understand a few things.
Once a connection is established...
In both the SDK and production specification (PS 1.4) it is noted that the TIMER (Timer / counter) peripheral in 'COUNTER' mode (0x01) is deprecated.
For implementing a...
In my current case there is a relay node to which want to send RSSI values of beacons nearby and then relay the same information across other relay nodes in the network, So...
what is the problem of "ERROR Failed to open nrfjprog: Error occured when open device long term. Errorcode: CouldNotLoadDLL (0x3)" , when i use the nRF Connect.
the version...
Hi,
How can we receive more than 20 bytes of data from the phone? We are using s132 and SDK 12.3. I know how to send more than 20 bytes of data from the NRF52 to the phone...
I am a newbie to Nordic chips and tools and new to bluetooth. My company is doing a BLE sensor. We have a prototype board ready and I am trying to do some firmware for it...
Hi I have tried the light demo example, where I do not understand the difference between "reply_Status" and "publish_State" on the server, then someone can explain the difference...
