Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
nRF51822_Development_Kit_User_Guide_v1.3.pdf document has table 6 which indicates SoftDevice A and SoftDevice B. DK includes s110_nrf51822_5.2.1_softdevice.hex. Is this SD...
Hi,
I'm testing a BLED112 USB Dongle from Bluegiga ( www.bluegiga.com/.../).
I have not been able to use see the Nordic Board advertising. Currently testing ble_app_proximity...
I was wondering would it be possible to use a 50 ohm IC Antenna ( like this one ) for the nRF51822 with the matching circuit given for the nRF24 ( link here )?
It seems...
Hi,
Is there any difference(data rate) between sending large data packets through single characteristics and multiple characteristics?
I have created one characteristic...
Hi everone!
I need to get a timer setup which repeatly fires 2 IRQs. The first i.e. after a timer count cc0=500 and the 2nd count cc0=700. After 700 ticks the timer value...
Hi,
I've noticed that when using SPI without a Soft Device or BLE function calls, the SPI peripheral is easy to control and operates correctly.
This nice operation stops...
hi,everyone.
I try to use ble urat sample for bonding by passkey entry.
and connection established and to bond. i try to entry passkey by uart.
but when i key the passkey...
Hi!
Can you please recommend a LDO IC for a USB/Li-polymer Battery power for the nRf51822 please? The LDO needs to drive the nRf51822 and a couple of sensors such as Gyro...
I'm trying to get the ble_app_hrs example working in Eclipse, but the stack pointer is not setup correctly. It's at the start of the RAM (0x20000000), and therefore it already...
I'm implementing an Android 4.3 app which uses an nRF51822 and the BLE proximity profile. I have the following as starting points for the app code:
The BLE sample...
I can't seem to find the required current of NVMC doing erase and write. The product spec has only timings but not more. Could someone from Nordic provide some figures? Experimental...
Hi,
I have a C# app connecting to 51822 devices, doing data/firmware download. When I try to send erase page command (before write), erase works, but there is a disconnect;...
