I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hello, I am trying to get a custom board with an nRF5340 (on a Raytac module) up and running. I want to emulate a simple HID mouse. Therefore, I selected the code from the...
I have just started using 2.7.0 with the nrf54L15 chips and come across a few problems.
When trying to run the UART sample I found that the app overlay files, which I believe...
Other than setting the DCDC_MODE_PIN, what else does the sd_power_dcdc_mode_set() do?
I'm seeing an issue where I have a GPS peripheral on UART that is seeing about 10dB...
Hi Nordic team,
Hi Nordic Team,
We are trying to configure two SPI masters. It works when I use any single SPI (only one), but when I add the second SPI, I encounter...
Hi,
I am trying to compile an old project.
I am using SEGGER_Embedded_Studio_Nordic_v568_win_x64 with nRF5_SDK_17.0.2
I am getting an error message for the following...
Does the 7002 support 802.11 monitor mode? https://en.wikipedia.org/wiki/Monitor_mode
Some chips call it promiscuous mode even though that should be something separate ...
First of all, I see that NRF52840 doesn't have a Real Time Clock but it has a Real Time Counter which is not working in case of sleep and low power mode, am I correct?
Second...
Hey everyone,
I am having trouble setting up the lsm6dsv16x as a interrupt. I was able to successfully poll the data meaning I can talk and read imu data, but no interrupt...
Hi , I wanna keep my existing mobile application which talks to nRF5340 over the BLE NUS service. I am using the default BT_UUID_NUS_VAL as my primary mode of communication...
I want to edit the explom firmware that comes with thingy91 to add the reading of new sensors and send them to nrf cloud. Where can I get the example of the Asset Tracker...
I have a custom board that started life based off of RF9160-DK 1.1.0.
We have a single programming header that can be used to program either the 52840 or the 9160 depending...
I've installed nRF Connect for VS Code Extension Pack v2024.9.5 to ubuntu 22.04 and after opening vscode the free disk space continues to diminish and cpu load is constantly...
Hello,
We are working on an integration between a nRF52832 and ST LIS3DH accelerometer on our custom board, using SDK 15.2.0 with SoftDevice and BLE enabled, and have observed...
The last couple of months I have been following the course “nRF Connect SDK Fundamentals”, but I am unable to get further than Exercise 2. This is because Visual Studio cannot...
