Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Hello,
I am trying to measure the RSSI value of the Zigbee communikation on nRF5340DK.
Right now I have programmed light_buld into one of the DK and light_switch into...
I have followed https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners-tutorial
i WANT TO ADVERTISE the battery...
Hi,
Segger SystemView 3.30 (downloaded from https://www.segger.com/downloads/systemview/ ) does not work with NCS 1.5.1. Upstream Zephyr has updated https://github.com/zephyrproject...
Hi Nordic,
I just had Thingy:91 few days ago. I ran this KIT with thingy91_nbiot_2021-03-04_8e8c6089.hex and asset_tracker example in ncs/nrf/applications . I found that...
I would like to send and receive data to/from nrf52832 pins over BLE using android phone. I would like to capture and display output of Force Sensing resistor and control...
To the kind attention of Nordic support team,
We have got an nRF52833 gzll host that has to interact with multiple gzll devices. We empirically saw that (in our case and...
Hello
I'm using the CLI example as ZC and a custom endnode based on the freeRTOS multisensor example (from nRF5 SDK for Thread and Zigbee v4.1.0). Im trying to send a counter...
Hi, I have a problem with setting up SHELL over RTT. I have managed to get some logs from the device. Prompt `rtt:~$ ` is also shown. but whenever I try to send something...
Hi,
we just uploaded MFW 1.3.0 to our nRF9160 DKs that had engineering revision of nRF9160. They seem to be now bricked and it is not possible to downgrade to MFW 1.2 via...
My task is to create a webserver on the nRF9160DK. For this i'm using the civetweb module provided by zephyr and the ethernet-shield from PHYTEC. I got an issue i want to...
Hi everybody,
I have developed a BLE sensor based on nRF52840 (S140 6.1.1 and SDK 15.3.0) that is normally performing connectable scannable undirected advertising. Since...
Hello,
I need to use the ADC with 600mV internal voltage, ADC Gain stage = 1.
The input signal on VINP vary from 750mV to 1750mV, and input signal on VINN is fixed at...
Dear friends,
I followed the tutorial( Using serial interface for provisioning and configuration ) control a mesh node.
a) The PyACI as a host via uart connet to 52840...
Hi, teams.
I checked the operation of nrf mesh network. (mesh sensor example, and light switch example)
It works well. Thank you!
By the way, I have a question....
Hi everyone,
I am having a problem with dfu example. I would like to test my board with the buttonless dfu image, namely
sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
