Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi All,
I have the strange issue with scanning. I have the project losely based on examples where I created peripheral adevrtising with 1s interval. This sends the custom...
Hi there, I'm using nrfutil ( nrfutil version 6.0.1 ) to dfu via ble (dongle),
Mac (10.15.2), windows (10), linux (raspbian) have been tried out to update the firmware none...
I am using the '840 to construct a small network using the ESB stack. In this design, a master (dongle) transmits to each slave and receives an ACK w/payload response. The...
I changed the way to get the upgrade program in the bootloader program and wrote a function to write the accepted bin file to the bank0 area. However, I found that it took...
Hi,
I am using BMD300 rigado board having nrf52. In my application i am tracking the ADXL362 accelerometer's motion.For this, I am combining SPI, UART(for displaying data...
Good evening,
after a very long research I couldn't find any answer.
Is (and if, how) it possible to connect an Arduino (or ESP32) via SPI, I2C etc. with the nrf52840...
Hi,Nordic Team
I tried to set 0,1,2 modes respectively in GNSS option, and the test current is as the attachment .
0 1 2
/**@defgroup nrf_gnss_psm_modes Values indicating...
Hi,
I am using nRF52832 with s112 BLE stack and SDK v16.0. I am wondering what is the most proper way for the "idle_state_handle()" method in the main loop.
Currently...
Hello,
I need to have connection status at the application level (IOS).
I'm working with the example "light switch server proxy" where the heartbeat profile is working...
Hello, I modified the instance in usbd_hid_generic to simulate it as keyboard. I checked the code of NRF52840 on github about the keyboard. It USES the function app_usbd_hid_generic_in_report_set...
Hello,
I really like your products since nRF51 but I noticed the same experience issues every time.
I tried your nRF9160 DK with the new SDK and I’m very disappointed...
Hello,
I am using NFC example "NFC BLE pairing reference", I could not paired with mobile phone through NFC. My android phone has version 10. The first time it paired successfully...
In my BLE project at the scanning side I see that application gets held if I remove filters from scan_init API and calls nrf_ble_scan_connect_with_target. I am refering to...
