Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I have a multiprotocol application and I'd like to do BLE scanning for as long as it's possible. For now I made 30% to 70% BLE to Thread, and it's the most I can give...
Hi,
I'd like to be able to use an event from the LPCOMP to sample the RTC (either to a peripheral's register, or to a memory address), so I can measure pulse widths without...
Hi there!
I am running the Thread Border Router example and have successfully loaded RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha.img into the RaspberryPi 3B+.
The problem...
Hi,
I've modified light switch client to read input from GPIO pins . I used int_pin_change as a reference for initializing inputs. The Int_change_pin example uses interrupts...
Hello, I'm developing an debugging an BLE application. I'm using nRF Sniffer (dongle) N51422 PCA10031. I can successfully sniff and decrypt ble secured connections of my application...
Hi all, I want to add light switch client to light switch proxy server . But I dont know how to get appkey handle for bind to light switch client . Pls , help me !! Thank...
Hello,
I'm unable to capture packets using the sniffer. Here are details regarding my set-up:
System: Debian 9.4 with kernel 4.9.0-4-amd64 #1 SMP Debian 4.9.65-3 (2017...
Many of the pins in the assignments page of the documentation are designated as "Standard drive, low frequency only" and I cannot seem to find an explanation of what is considered...
I am trying to connect my android mobile with nRF 52DK using BLE on the NRF TOOLBOX android application. But the nRF 52DK is not recognize by the NRF TOOLBOX APP(proximity...
Hello,
we have a problem using the SAADC module with the low power mode, particularly after execution of the NRF_SAADC->TASKS_SAMPLE task.
Before taking a sample, the...
Hello,
I have some questions about ble_conn_params.c in SDK14.2
Question :
1. a. Why do you need to handle four ble conditions ?
b. Shouldn't just send connect parameters...
I hope to use a acceleration sensor with nRF51822 dev kit. So I should use three ADC input. I tested getting one ADC data using adc_simple example(Keil_v5/ARM/Pack/NordicSemiconductor...
