Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
What is the exact sequence when reading a characteristic with variable length and authorize required.
When I have a actual data length of 14 I can read with offset = 0 and...
Hi All Team Members,
Using Nordic Development Kit of nrf52832 I am able to write and test basic application using UART and BLE
using this kit I get the following error...
Hello, I use a custom board with nRF51822QFAA, with two buttons (left, right) and uart for printf/debug. The idea of the project is to have the board always sleeping, it wakes...
Hi,
I have a project which need to use two UART interface at the same time.
As well known, there only have one hardware UART interface in nRF51822/nRF52832. If I want...
Hello, DevZone,
I have programmed an nRF52-DK with the unmodified SDK's ble_app_hrs_pca10040_s132 (heart rate monitor) BLE peripheral application. I also have a Power Profiling...
Hi Susheel,
Thank you for your support.
We would like to get your advice related our new design, with the followings:
Assume we need to support besides of the BT5...
Hi,
I am developing one of the my project on custom board, in which I have to configured the two GPIO Pin's as input to sense the those pin and take actions assigned on...
I'm developing a battery powered BLE sensor application where I need some basic guidance on how to implement this:
The sensor action consists of a measurement process where...
Hi there!
I appreciate your work on Nordic SDKs which are getting better and better.
But sometimes SDK setup isn't as quick as it could be.
E.g. for evaluation purposes...
Hi,
I am trying to port the Thingy project (ble_app_thingy_s132_pca20020) to Segger Embedded Studio on a Mac and it proved to be not an easy task, in fact I have hit a...
Dear all, I am building a BLE thermometer based on nRF51422 chip. I need to get certify it and if any of you performed and have the tests results of the below tests, for the...
The board came pre-programmed for MBED. I don't need that, wood like to enable regular JLink. I believe the process is to get it in boot loader update mode (hold boot/reset...
Hello,
I am new in this platform. Few days ago, my boss give me a nRFgo Motherboard. He want me to write a program that nRF24le1e can read/write data from sensor via I2C...
Just verifying to be 110% sure:
The TRACEDATA1-4 pins may be used as ordinary GPIO pins when no trace-functionality is configured for the debugger? So even if a debugger...
Hi,
I have a PCA10040 connected with some wires to an external I2C device and I need to poll data from the I2C device and send it over BLE, also updating the advertisement...
