NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
When I compile the attached example project like this:
I get the following warning:
And the compile flags for main.c (taken from compile_commands.json) are:
I...
Hi all !
I recently faced an weird issue with a nRF5340 (on a DK board, and then a custom PCB). When writting to the PWM peripheral, configured to some GPIO pins, some...
I am trying to run central_uart example which is failing when bt_settings_init function is called. I debugged further and found that
settings_subsys_init is called inside...
Hi all,
I need to generate two 1 MHz signals with opposite phases. However once I configure the decode mode as "Individual" I don't have output signals. In case of "Common...
Hi,
Where can I find the nRF9151 CE/RED RF test results for the purpose of CE delta certification of a new product based on nRF9151? (i.e. leveraging existing nRF9151 certification...
I am trying to configure the absolute time in my application, which at some point receives the time_t epoch value from an external source and should update it internally so...
Hi ! I have 5 different bootloaders for 5 pieces of hardware that I would like to cycle test OTA DFU with BLE. I have some questions
Why does nrfutil dfu ble require a...
Hi,
after having issues with my devkit flashing the main MCU, the interface MCU isn't being seen on USB anymore.
LED5 is blinking rapidly.
The board is a PCA10040...
I am creating a custom board with an W25Q128JVPIQTR external flash drive using SPI with a nrf5340. The pins are:
P0.08 - SD_CLK
P0.09 - SD_MOSI
P0.10 - SD_MISO ...
Regarding the operation of EJ2832AA1 (nRF52832), Please answer the following questions. nRF5 SDK ： v15.3.0 SoftDevice ： S132 v6.1.1
I am doing UART communication with another...
Hello, I am new here and I hope to not duplicate any other similar post (to be honest I have search a lot before writing). I am working with nrf52840DK, I have used blinky...
We're trying to set up MQTT messaging between our custom nRF9160 device and our private AWS VPC. When using the Serial Terminal in nRF Connect for Desktop to monitor the device...
I am reaching out to request assistance regarding a FOTA (Firmware Over-The-Air) operation using the HTTPS protocol for my new nRF7002-DK development kit. I have successfully...
Hi
I heard about that RSSI has no relationship with disconnection. However, based on my experiments, the connection will break every time I am close to -80dBm.
I am confused...
Does anyone know of a good starting point for Bosch BHI360 IMU integration into nrf5340 and Zephyr?
Did look at: https://community.bosch-sensortec.com/mems-sensors-forum...
