I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I'm working on the UART with BLE application example. I'm trying to see into which struct does the characters entered on the screen gets saved. From the documentation, the...
we now using GPIO as input. when it rise then start timer. but it seem failed. No GPIOE IN event happened.
what's timing need for rising/fall edge detecting? < XX (us)...
A a couple of years after initially giving up on BTLE (due to Apple's refusal to implement reception certain advertising modes) I am back to have another go at it.
Basically...
Hello
This is probably a very simple problem to solve but I'm having trouble disabling an RTC0 interrupt by using a GPIOTE PORT interrupt on an nRF51 board.
Basically...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
If my way of thinking is not wrong, I have to set SEVONPEND flag to wake up cpu from sd_app_evt_wait on pended event. How to set this flag? I cannot find any function/macro...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hello.
I used sdk 5 and 6 without much problems in the past, but thought it's time to upgrade.
I don't seem to be able to get even the blank blinky example to work for...
Hello
I'm using S110 with nRF51822.
I'm trying to implement some logic which is quite simple, but for some reason things are not working properly.
I'm advertising...
Hi all,
I have failed when try to flash a new softdevice s110 to the target device is Wunderbar's sensor module which is using nRF51822 chip. Flashing application has no...
Hello,
currently I am using the S110 Softdevice with the ble_template example as peripheral. This works fine.
For our final application, we need the central feature...
Question similar to this one
devzone.nordicsemi.com/.../
I have noticed that in the header ble.h included in the s310 folder, the function sd_ble_enable(..) and the type...
Hi Nordic expert, I wanna get a profile of 51822 performance cycle count. I found 51822 has no powerful DWT feature as cm3 or cm4, would you share me some feasible methods...
Hi All
I am aware that there are some changes to UV5.12 to do with Device Pack location etc.
I have currently updated my project from the .uvproj to .uvprojx extention...
