Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Now that I have TWI and the BLE stack initialising, I'd like to create services. The Server (peripheral) sends out a few bytes to the client when a local trigger happens,...
We're working on a project with the nRF51822, but most of our developers are working from OS X and Linux. Is it possible to flash the softdevice from these platforms? Also...
Seems like the timer API uses low priority interrupts. Now, I dont need the timer triggers to be exactly delivered so that is fine ... however, i do need to know the exact...
Hello. I've used the design template that initialises everything for Bluetooth communication. These are the initialisation calls made in main():
// Initialize
leds_init...
I have to use TWI(I2C) interface to configure sensor.
Now ,i reference "nRFready Smart Remote " project drv_gyro_mpu6050.c .
and change the register number ' configure....
I want download ios app demo source code from www.nordicsemi.com/.../nRFready-iOS-Demo-App
it say :"please enter your product key once more for access "
How can i get product...
hi, I am having problem trying to get the app_uart.c to replace the simple_uart on the blinky example with PCA10001. My uart param as follows:
void uart_event_handler...
Is there an example firmware project available for a Gazell Host using the pairing functionality?
It would be nice to have the host code of the "Gazell Pairing Desktop...
In connection with a nRF51422 evaluation kit, I installed the Keil development tool in a non default path then subsequent installation of nrf51_sdk_v4_3_0_27417 produced a...
How does the nRF8001 chip generate the passkey in the DisplayKeyEvent? Is it possible to set this passkey from the App Controller?
As I understand it, the SetKey command...
I find this strange but I can program the HRM demo fine but with my own code it compiles with no errors or warnings but will not program with Error: Flash Download failed...
Hi Nordic,
I want to develop a PC software that works as a master device which can scan for advertising packet, establish connection, etc. Basically, something similar...
Dear Sir,
After I remark this //BLE_GAP_CONN_SEC_MODE_SET_OPEN(&cccd_md.write_perm); and program it into nRF51822, then I cannot program it again. PC program report it...
I have modified the included HID mouse example to allow for left/right/middle mouse clicks. However, it is not clear to me how to set an event handler for both when a button...
