Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hi,
I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for!
My device has a power enable pin (on GPIO1) that must ideally...
Hi
This isn't about a problem so I'm not sure if this is an inappropriate post to make here, if so please feel free to remove it, however there is no commercial incentive...
Hello everyone.
Absolute novice here but a lot of reading over the last few days has brought me here.
I'm currently watching a little robotic project being developed....
Hi
We have developed a remote-control system where both the sender and receiver are built around nRF52840. Today, the SDK is sdk-17.1.0. We are now considering moving over...
The Nordic Hardware Design Guidelines suggest a 0.050 mm soldermask clearance around the pads which should give a 0.100 soldermask sliver between the pads according to the...
Hello all,
Currently I am working on getting the nRF Mesh DFU target and distributor samples working in the context of our project. This appears to have been successful...
Hello,
I have been chasing this problem for some time, but it has been difficult to capture.
The issue occurs when the device is sitting idle (no eDRX or other power-saving...
Hi,
I'm evaluating Wi-Fi NAN (Neighbor Awareness Networking / Wi-Fi Aware) for a project and came across the nRF70 Series, so I wanted to check on the current status and...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hi
I'm building firmware for the nRF54LM20A running USB HID + ESB at 8 kHz. Currently I am referring to the nRF Desktop ( nrf_desktop ) sample as a reference. But there...
We have thousands of devices live in production and we sometimes encounter the situation that we cannot restart bluetooth advertising anymore after a connection attempt. ...
Hi
We are using the nRF52840-QIAA-R in a lot of PCBA, now I see there is a new revision nRF52840-QIAA-F-R and the old type is not recommended for new design.
What is the...
Hello! Sought out to upgrade from NRF SDK 3.1.1 to 3.4.0 today so downloaded and installed it on Mac using nrfutil sdk-manager command line, and that was fine. The project...
Hi,
In our PCB using the nRF54L15, we used different P2 pins for the sQSPI, believing after reading the docs and driver API, that one could configure different pins than...
Hello,
I have some trouble to identify my custom nrf52832 board in the VSCODE.
To program the board I am using nrf52840dk, and connect it to my board as follows:
...
