Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I'm doing migration from sdk 1.9.1 to sdk 2.1 according to procedures mentioned in Migration Guide. All dtsi migrations were done sing script and later on manually reviewed...
I am using the NCS (2.0.2) SMP SRVR example with the bt-overlay.
I can connect via Bluetooth, but once I start the DFU update via nRF Connect I get an "Authentication is...
I have AES ECB encryption working on the NRF5 system, but I cannot get it working on the Connect SDK.
I have found CONFIG_CRYPTO_NRF_ECB config, but this seems to require...
Hi!
I'm trying to run SPI slave on nRF5340 - doesn't work - project doesn't even build, the SPI master is running.
Can I see an example of NRFX SPI Slave for nRF5340?
Hi, I have several issues just to start off with. One is when I generate support information, it does its thing, and then stops, and I have no idea where the support information...
Hello,
I am looking for the detailed schematic of the debugger board which is packed along with the Thingy:53.
I need to understand the detail pin configuration for...
Hello there,
If I init a UARTE module (nrf_drv_uart_init) with e.g. Pin RX = 3 is it already enough to just disable the module (nrf_uarte_disable) so I can use the RX...
MCU: nRF52840
IDE: Keil uVision
SDK: 15.2.0
Board: Custom
Hello,
I realize there are a ton of threads about this, but none address the specific question I have...
Hello,
My board is powered by lithium-ion batteries.
It works from 3V to 2.1V. And It stop working at 2.1V.
After discharge, I re-charged battery. But It doesn't work...
I want to achieve reproducible builds on my development machine and a gitlab CI/CD server. So far the generated binary differs if I build locally (VS Code + NRFConnect SDK...
nRF5_SDK_17.1.0_ddde560
nrf52832
Cache overflow at baud rate 921600. I use the register to complete the serial port driver. I don't know how to use registers to implement...
To the kind attention of Nordic support team,
I'm testing a freertos project, with softdevice and radio notifications. A constant number of notifications is queued before...
Hi guys. I saw a previous post saying the LE Power control not supported.
For nRF Connect SDK v2 / nRF52 or nRF53, are there updates on LE Power control?
Since that...
Hi there,
I have just started the NCS Fundamental Course and I am stuck on Exercise 4 Lesson 1 and Lesson 2. There are two problems that I am facing.
1) If I use the nrf52832DK...
Hallo,
up to now I worked with nRF52840-DK 2.0.1. After compiling, flashing the board was quite comfortable by means of the JLINK drive, which automatically opens after...
