We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hello there,
I'm using a nRF52840. I would like to perform a complete flash dump. I have tried using an ST Link V2 and and openOCD. It was only returning errors and the...
Hi,
Im using: nRF Connect 1.9.0, Visual Studio Code. I have: a nRF52480-dongle a nRf5340_DK
I would like to have Samples (code), to have a loop through with the highest...
i have a code base which is originally run on nrf52832 dk and i want to port it to the pca10059 dongle i run in gcc env and successfully modified the definitions and includes...
Hi, I'm developing an project based on ble_app_uart example. My expection that is multi mobile phone can connect with my nRF. But, my nRF can connect and communicate with...
Hi Nordic! I'm using the nRF9160 with a micro sd card so I have a lot of storage. I was wondering if it is possible to retrieve a .hex file and flash it using LTE?
I'm able...
Hi,
When I try to build a 'light_switch' project on SEGGER embedded studio for nRF connect SDK 1.9.1 for BMD-330-EVAL board. Running into the following error
arm-none...
Hello Everyone,
I am using NRF52833 in my project and I have my NRF module connected to 2 other microcontrollers on UART peripherals. The details are mentioned as below...
We have first worked with a development kit from Nordic (nRF52840 DK) . We flashed the BLE applications using the nRF Command Line Tools.
https://www.nordicsemi.com/Products...
Hello,
I have to open a new discussion session on the same topic because the current session has been closed.
The topic is as follows: devzone.nordicsemi.com/.../at...
Hi,
We currently have a Gazell project that runs on nRF52832 . We have difficulties changing the project target to the nRF52810 .
From the SDK17.0.2, example: "gzll_ack_payload_device_pca10040...
Hi,
I have a firmware (performing DFU over Bluetooth )that runs well on nRF52833 dev kit and for developing the DFU over BLE. I follow this tutorial
https://devzone.nordicsemi...
Using SDK 17.0.2 I wrote a function to modify advertising interval on the run. The function doesn't return any error but the interval isn't changed. What am I doing wrong...
After nrf_drv_twi_tx() function and nrf_drv_twi_rx() function, m_xfer_done is checked using APP_ERROR_CHECK(m_xfer_done). What is the significance of checking m_xfer_done...
Hi,
I am working on DFU-OTA example on BLE. my doubt here is once the controller copied the image into slot1 bootloader will immediately start to validate whether the image...
I am using the following code to generate and output a n-MHz clock on a GPIO pin. (code is borrowed/copied from another question on this forum)
However, the clock output...
