Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi All,
I've run into a weird issue where my SPIM rx buffer remains empty (it's not even filled with garbage - just empty). Am I operating the SPI drivers properly? My...
Dear,
When I try to use <nRF Connect for Desktop>, it will show this message below:
I checked, this is because the first web which is based on America, can not be opened...
Hello, we are currently using the nRF51822 chip, and have roughly 1000 units of this particular device out in the field. After a few months of use, approximately 20 of these...
Hello,
I came across a very consistent bug that occurs on the nRF9160DK and a custom board with an nRF9160.
Basically, if you try to send the AT commands "AT+CFUN=1...
Hi,
I'm working with Nordic nRF52832 and trying to install Nordic Semiconductor nRF CPU Support Package from SES, from Tools--->Package Manager.
However, I wasn't able...
Hi
I want to use the NRF52840-DK board to evaluate some circuits that communicate with the nrf52840 chip. I want to design the board to act as a header for the hevelovpment...
Hi!
I want to be able to configure my nodes (assign AppKeys) from my own mobile application. I would like to know if it was posible to provision the nodes from the nordic...
Hello,
I am using NCS 1.7.0 for our latest product development based on nRF5340.
We have previously used Open source zephyr project for our development. We have an application...
Hello, devzone. I'm developing end device on nRF52840 using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0. I've connected my device to Home Assistant(HA) and have some configuration...
I need to use both AIN0 and AIN1 of nRF52832. AIN0 is measuring once per minute and AIN1 is measuring once per second. What would be the best approach for this? Thanks
Hi, I'm trying to reading the data pins of a camera and store it in variable. I'm able to read single pins using
How would I read 8 data pins simultaneously. This is my...
Hi nordic. I want to turn on and off the modem of the nrf9160 when I'm not using it. When I am using it, I am using your FTP library to sent sensor data to my server. Here...
Hi everyone,
I am working on interfacing the nRF52840DK with a 24-bit mems microphone INMP441 through the I2S peripheral. As multi-sources pointed out that the nRF52840...
I'm using macOS 12.3 and Python 3.9.10 from brew. When I "pip install nrfutil" I get nrfutil-5.2.0. Trying to run that results in "NameError: name 'xrange' is not defined...
