Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi , I want to send a char data through bleutouth using ble nus I am using this method
I don't have any error but I don't receive any information on my android application...
I am using nRF Connect for Android and had a question about a script I would like to develop: for this script, I would like user input to specify part of the value I write...
On the nRF 52840, is there a way to have the TWIM peripheral suspend a transfer after transmission of a single byte? The TWI peripheral provides the BB_SUSPEND short, but...
Hi engineer,
i am running a example:SDK 12.2/ANT/ant_bpwr,MCU:NRF52832;i want to dynamically modify the value of "CHAN_ID_DEV_NUM" by reading the UICR value for distinguishing...
I am trying to figure out how to use the SAADC component of the nRF52840 to measure an analogue input and report it as an attribute in a Zigbee end device. I have, so far...
Hello,
I am analyzing the DKs power amplifier characteristics as an assignment for university. I got the serial_lte_modem running and send AT commands via UART from an external...
Hi,
I am looking for a 4G module with in built gps in it. It has to work in european market, need to have esim facility.
Can you provide with the product links.
-
...
Hi, I am trying to code an AoA transmitter using the direction_finding_connectionless_tx sample project as a basis. I am using nRF Connect SDK v1.6.0 with nRF52833.
I am...
Hello,
I am having a few problems when trying to check if the nrf52 is dfu mode with my python script.
For that i was trying to get the firmware version from the dfu...
On Mac OS X Big Sur using the nRF Connect 1.6.0 installation in Segger the documentation suggest that to add a new source file to a project one should right click the project...
Hello, I tried to run the following command on my nRF52832 today and it reported an error.
The operation before the error was: I enabled APPROTECT, and when my colleague...
Hi, I made a mistake while working with a custom board.
I run "nrfjprog --recover", which obviously clears UICR, and then I powered the board off without writing the new...
I have a custom board with 3 nRF52840 chipsets, 1 central module is connected to 2 side modules.
The central module communicates with each of the side modules using UARTE...
Hi!
There is an end device that measures the temperature. If I calibrate the ADC during initialization or immediately after startup, the program hangs. If I start the calibration...
