Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
Hi,
I am using nRF52832 and SDK v15.00 for development.
I am working in ble_app_uart peripheral example. I have a task where I need to configure another UART communication...
Hello Everyone,
we are using Nordic's nRF52840 controller with SoftDevice S140 and the default Bootloader(C:\nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10056_ble...
Hello, I am working on a nRF52840 and started with the SDK15 gls bonding example. The device has no buttons or display so we are stuck with 1v2. We are hoping to incorporate...
Dear friend，
I want to implement ota data packet request through my own code. In the \examples\zigbee\ota\client example, line 876-1268 of zb_zcl_ota_upgrade.h finds the...
Hi there,
I'm using a nRF52-DK for a while, but now I made a bad misstake: overwrote the interface firmware. I pressed accidentally the RESET button and flashed a wrong...
We use NRF52832 in the remote control of the car。 We measured the average current of power consumption at about 1uA.Every 300ms, the current curve bounces to the transient...
Hi all,
I have two questions about BSP buttons management.
I see that the BSP supports the short press and long press for a button. However it seems to handle only one...
Hello
I want to read the values of two potentiometers from the Ain0 pin and the Ain1 pin through SAADC.
I could easily read one value through the saadc example, but I...
Are you able to enable internal pin pulls for UARTE pins, specifically the selected RX pin?
On page 490 of the nRF52833 datasheet, footnote '35' states that "High baud rates...
Hi Nordic Team, I have been working a project where I will need to send audio using I2S protocol to an audio chip. The audio chip will only accept a select set of values for...
Hi
We searched a lot of stuff regarding FOTA update in nRF52840DK using Lwm2m and coap protocol. But we could not get help in the right direction. We could not find any...
Hi,
In our app, we have updated from NCS 1.3 to 1.4 and suddenly calling bsd_shutdown() blocks the whole application for up to 10 minutes. Probably it is now waiting on...
We have the second device here, and I redo the programming now. First I download thingy91_fw_2020-10-30_5522ca2b to PC and then run programmer.
Then I selected the device...
Hello,
Is there any example to follow in order to interface an External NOR flash memory with NRF52832, using the newest version of the SDK ( v17.0.2 )?
Thanks in advance...
