hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
I have a nRF51822 module programmed for custom service and characteristics. I am able to connect to this module using android 4.3 API. I can get characteristics and their...
First of all, let me say that I've read some of the other topics, and I clearly don't belong here haha. I'm not at all knowledgable about electronics and the inner workings...
I wonder if a couple (or three) of your module with PCB antenna as receivers could be used for triangulating the transmitter, could I have some hints about this, or a schetch...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hello, I would like to know if the adress byte that is transmitted after the preamble is the MSB or LSB.
I've read the datasheet's page 28 and it's not very clear, it just...
I need to have an iOS device send my nRF51 some commands, some settings, and retrieve some data, not at regular intervals. The nRF51 should only-speak-when-spoken-to.
I...
Hi guys,
I want to use the nRF51822 as a gateway to send uart-commands from the µC to my iPhone and vice versa.
µC---|uart|--->nRF51822 ) ) ) ) BLE ( ( ( ( iPhone
...
Hi,
I am using the NRF51822-CEAA flip chip package for my custom board.
Because this package has an optical vulnerability from the sides, could you please advise how...
Hi developers,
I recently had a problem with nRF51822 and radio interrupts.
My situatios is quite clear but I cannot resolve the problem. I hope You will help me.
Description...
hi,everyone.
because of careless,i enabled pin reset in debug mode by set bit 0 in RESET register in my software,and i downloaded the hex file to a 51822.now,because of resetting...
Hi all
According nRF51822 Product Specification , GPIO pin can config to SPI interface. Means if I set a specific GOP pin range to SPI and connect these pins with...
I am successfully sending data from the PCA10001 Evaluation Kit to the Master Control Panel. But I cannot find any information about initiating and sending data from the MCP...
Hi,
Here i am attaching my text file. in my case timer api is working
but button event handler is not calling.
Kindly tell me , what is my fault.
Regards
Balaji...
I want to store a block of data in nRF51x22. I tried the following:
void HalStoreNVMBlock(uint32_t size, uint8_t* pBuf)
{
nrf_nvmc_page_erase(NRF_UICR_BASE);
nrf_nvmc_write_bytes...
