Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hello,
I need to write to the UICR flash multiple times. Typically, this involves disabling the softdevice, writing to the UICR, and then re-enabling the softdevice. However...
ncs v2.6.1 nrf5340
As mentioned in the document , Q1. Does CONFIG_BT_MESH_PROV_OOB_PUBLIC_KEY need to be set on the provisioner's side as well? The document only mentions...
Hello
NCS2.3.0 or newer, is there a demo BLE HID ?
connect to android phone for control play/pause music.
i.ve found ble_app_hids_mouse in SDK 17.2.0. it can play...
I was trying to setup a nordic nRF9160DK following the steps present on the first lesson of the course "Cellular IoT Fundamentals", and fail to do so. When I got to the verification...
Hi,
I have used PPK2 to measure nRF9160 current using different boards. I like the product, but I'd like to note is that there seems to be a typo in the PPK2 documentation...
Hello,
When we try to run the standard radio tests for bluetooth, we get really low power compared to what is expected (difference of about 32db). Turns out SW_CTRL0 was...
Hi there, I am working on SMP client server application where I want to do the DFU of server from the client side where both the server and client are nrf52840 dev boards...
Hi,
I followed the instructions listed in Installing the nRF Connect SDK (nordicsemi.com) . Then I followed the steps in How to create and build an application (nordicsemi...
I am working on nrf52832 development kit for interfacing SX1262 Lora module via SPI. I have configured SPI 0 as follows:
Initially I am trying to read the SX1262_REG_SYNC_WORD...
Device/Board: nRF5340 DK Application: Mesh Light (Bluetooth Mesh Network)
Use Case: I am currently working on a Bluetooth Mesh network using the nRF5340 DK. My goal is to...
Hi,
We are using nRF SDK 2.6.1 and have selected the nrf7002dk_nrf5340_cpuapp target. After adding CONFIG_BOOTLOADER_MCUBOOT=y to the soc_flash_nrf example,
the code fails...
Hi everyone,
I have a problem about MBR and Bootloader memory (at address 0x74000). I am using nRF52832 S132 v6.
My purpose is that I can upgrade bootloader from inside...
I would like to wake my app from sleep (k_msleep) on a GPIO interrupt. I'm finding that enabling the interrupt draws an additional 6uA however (8uA vs 2uA without it) - am...
I would like to set a gpio pin on Radio RX Ready and clear it on Radio Disable all via PPI. Below is my code. I only get the pin to change levels when the OUT task polarity...
