Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Hi,
nRF Connect SDK 1.7.1, windows 10 X64
run SEGGER Embedded Studio.cmd or click segger_embedded_studio IDE menu File->Open nRF Connect SDK Project,
it will be got...
I have impulses coming to a GPIO input. Each pulse (say: rising edge) should toggle some other's GPIO output. What I know, is that I cat apply a task to a GPIO output. This...
I am using nrf52832 board sdk vr 17 s132 soft device. I want to have a way by which i can reduce the brightness of led while it blinks during advertising mode using PWM. pls...
Setup mcuboot and dfu to upgrade firmware on the nRF52840 of our board. Upgrading to new firmware works as expected and the new firmware is running after the install. If I...
Hi，
I am using nrf52832+freertos to develop a low-power product based on the example(ble_app_hrs_freertos) in the SDK, but now I find that the power consumption far exceeds...
Hello Nordic! I have connected a sensor to the DK via SPI. It outputs a lot of data, a lot... for 1 second of data I get 4096 entries. Each entry is 10 bytes in length.
...
I'm working on a design featuring two different MCUs. I'm looking to use the nRF52840 as one of them. I need both processors to be able to send each other messages and ideally...
Hi,
I have a weird problem. My application starts two timers, one after another. Like this:
Normally it just works - no errors, nothing. However, after a DFU OTA upgrade...
What is the best method to store TLS certificates on the nRF5340? I have seen 2 options, but I'm not sure what is best practice and what does work.
If I store the certificate...
Hi,
i just got my hands on Thingy 52, just want to know how do i get started in retrieving data from it, specifically for motion(accelerometer data), if someone can point...
Hi,
I'm trying to interface LR1110 (Dev Board) with NRF9160 DK using SPI. I have been working on this for a couple of weeks, explored almost the whole devzone, learned a...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
HI,
I need to check the following thing with you. I need to use an I2S mic with NRF5340 between the mic and the controller we need to place 2meters of wire. So, I need...
Hello All, I'm currently working on an application with a central and peripheral devices both using nrf52832 with SDK 15.3 and S132. I'd like for the central to be only trying...
