Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Recently, we are using Nordic resources and developing our own application. We have blue tooth integrated in app, also we have display and our own file system integrated on...
Hi,
I'm working with nRF52840 DK and I want it to advertise iBeacon packets.
I tried the beacon example on ble_peripherals from nRF5_SDK_15.3.0 SDK.
1) nRF connect and...
Hello,
My project is on nrf51822 in which I am using BLE and UART interfaces.
There is single UART available on nRF51822 and I am using it for communication with an...
Hi I am using the custom_ble_service example from https://github.com/bjornspockeli/custom_ble_service_example/blob/master/main.c . The example code will turn a custom characteristic...
HERE is the fix for this problem. It has been reported before (by others) with no reply. I hope that this fix or its equivalent will be incorporated into the next SDK release...
I want to interface a 16MB external flash (SPI) with nrf52832 on the development board.Suggest me how should I start with and if there is an example for external flash then...
Hi Great Support Team:
In the spec of 52832, the rx sensitivity is -96dBm @ 1Mbps.
I'd like to know if the sensitivity is the same (-96dbm) while we adopt ANT+ protocol...
I am using the nrf52840 with freertos and bluetooth (based on the HRM example). Application is designed to sleep for a set period of time before the RTC timer wakes the MCU...
Dear Nordic Team,
Due to a mistake i flashed a bootloader-firmware with the compile flag CONFIG_GPIO_AS_PINRESET onto a custom board where pin P0.21 is tied to ground ....
I just received my nRF9160 DK. I got it connect with the nRF Cloud (with LED 3 and LED 4 blinking). I then started nRF Connect (Programmer) and the application crashed. I...
Hi all,
I want to ask whether I can put the main app on random address in the flash of the chip if there is bootloader and SD present due to future releases of SD and memory...
Hi. My application is scanning ble beacons for 1 sec every minute, and I want to store this data in an array to be sent every 10 min. I am getting the data in BLE_GAP_EVT_ADV_REPORT...
Hi,
I want to implement a Peripheral (GATT Server) that automatically starts notification once a Central connects. No bonding is provided in our system (connection is between...
Hi,
I'm in the early stages of developing a BLE peripheral device that requires the use of the CC310 CryptoCell on an nrf52840-DK board.
I have managed to implement a...
