Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to interface ADXL372 with nrf51822 using SPI interface.
Tried merging this code in SPI master example:
https://github.com/analogdevicesinc/arduino/blob/master...
Hello,
I'm trying to program a nFR52840 USB Dongle so it can connect to other devices through BLE (another dongle, for example). I'm new to this platform so I've been...
hi......
how to choose the correct slave address , i am using max30205 peripheral device , in that datasheet there are three A0,A1,A2 pins with different combinations address...
Hi
I'm using this code ! And I'm not sure that it works well, so I've been trying to send a data from one divice to an other, but my problem is where can I find the received...
So I've been trying to integrate the ble_nus part of the ble_app_uart example into another project. All inits and sdk_config options seem to be the same.
Still, whenever...
Hi,
I want to read a IC register over SPI.
This is msp430 code,it works. Just
CS low
write address
write 0x00
CS high
I use SPIM, this is initialization
...
Using an nRF52832 with SDK15.2 can I have multiple SPI devices;
one with DMA and one without DMA?
And can one instance be of legacy type (nrf_drv_spi) and the other be...
We use Rigado BMD-300 module with nRF52832 and softdevice S132 v6.1.0 as peripheral. Trying to create test plan for Bluetooth qualification , but with new TCLR there are inconsistencies...
Hi,
Recently, I faced very weird problem which stops working MCU when MCU enters low-power mode.
Not all PCBA I made have the same problem but quite many PCBA shows the...
hello, this is my first time to start the PPK, I have a 52840 DK (BMD-340-EVAL) and PPK, when I use nRF connect to connect the PPK(PPK is over the 52840 DK) , it shows Failed...
Hi Nordic Community
I'm busy developing a board around the nRF9160. Do you have a KiCad library/component for the SOC, do I need to make one myself, and if you do have one...
I'm trying to use the SPIM driver on nRF52832. The setup is:
Chip: nRF52832
SDK: 15
Softdevice: s132 v6
Toolchain: GCC
For some reason the call to nrfx_spim_xfer...
Hello,
I'm trying to configure the max -min of interval params and supervision timeout to obtain timeout of android = 1s.
i configure all parameters to run function...
