Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
SDK Version: 9.0.0 Softdevice: S110 v8.0.0
I'm currently trying to send streams of data from an Android app to a nrf51. However, at some point, Android side writes to the...
Hello,
Our device based on nRF51822 with SD110 v.8.0.0.
The firmware use defined area in top of the flash to store some data.
The "RAW" functions sd_flash_write and sd_flash_page_erase...
Hi Team,
Is it possible to scan on one channel and advertise on another channel?
Say node-A will scan on ch-37 and advertise on ch-38 while
node-B will scan on ch-38...
I'm trying to use the NRF51DK to talk to this EEPROM ( www.st.com/.../CD00290537.pdf) . I've started by trying to modify the twi sensor example. One of the things that's different...
I am new to nRF51:
how do I change the softdevice from 110 to 130 in the example project ble_app_uart (and in general) within the Keil µVision IDE.
There is no option...
Hi,
I am developing a product for the 433MHz band. Due to the space constraints I had cut the ground plane to very small and also had to rearrange the components away from...
Hello everyone,
This image was copy from "infocenter.nordicsemi.com".
I'm trying nRF51-DK (IoT SDK) with Coap server , (raspberry pi with Coap client by python example...
Hi,
we are using RTC2 with APP_IRQ_PRIORITY_LOWEST. But the code hanged inside the interrupt handler. when we did step through debug, we came to know that in nrf_drv_common...
In nrf52_SDK/examples/peripherals/rtc we tried adding the UART prints and verified. It was working fine for RTC0 but fails to do for RTC1. Could you please give any hint on...
Hello together..
i have a problem with the nRF51 DK.
I tried a little bit with this DEVkit i.e. copy the blinky example to the JLINK storage.
This works fine.
Regarding...
Hello,
I am developing a new product using S130 on nRF51822(QFAC). My product use LCD as spi interface and ADXL345 sensor as i2c interface, also test it, works well without...
Hi all:
To saving power I implement the function to read data after interrupt is triggered..
below are my codes..
My expectation is..
Let CPU enter idle mode to wait...
I am trying to set up a GPIO interrupt, and found that whenever Button 1 is pressed, if Button 1 or 2 is pressed later, the app will reset. This is even if there is any other...
Hi.
I want to make a device which can connect each others and communicate with NUS.
I need not to use any other service without NUS.
I made nus_c service which is a central...
Hi
I can't seem to find this in the datasheets, what is the active current consumption of the nRF52832 chip, I'm interested in the maximum expected current consumption...
