hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
I am developing a custom board using the nRF9151 module controlled by an external host microcontroller. The nRF91x1 is running the Serial LTE Modem (SLM) application.
In...
Hi Nordic Support Team,
We are currently developing a product based on the nRF54L05 SoC using nRF Connect SDK (NCS) v3.0.0 . Our application is facing significant Flash...
Hi,
I'm using nRF5340 + nRF7002 for project that use wifi but I have issue while reading the default MAC before recording a new one.
The products are tested inside a...
When debugging the exercise 1 application from `Lesson 2 – Reading buttons and controlling LEDs` of `nRF Connect SDK Fundamentals`, I cannot set a breakpoint wherever I want...
Working in a Windows 64 environment with nRF Connect SDK v1.5.0. Target is a custom nRF5340 board connected through a nRF5340-PDK as a debugger, via USB.
I can no longer...
Hi,
I am developing a custom PCB based on the nRF52840 and am currently trying to flash/debug it using an nRF52840-DK (PCA10056) as an external debugger.
connected devices...
Hello
nPM Power UP v 2.24 detects nPM2100 EK, but does not detect the CR2032 battery. The active battery model selected is CR2032 and the fuel gauge is enabled.
I placed...
Hello,
We currently use an nRF51822 device in our product with the top marking QFABC0 .
We understand that NRF51822-QFAB is the ordering part number, and that QFABC0 is...
I'm working on a project for the nRF54L15. Until now I have not been using mcuboot, but since I added SB_CONFIG_BOOTLOADER_MCUBOOT=y to my sysbuild.conf, I get an error when...
in the datasheet table 80 "GPIO port mapping" the function "CAN-RX" is only listed on P9.4 and P2.8 are these the only two pins it can be assigned to ?
I am struggling to...
Hi Dev,
Development platform: NRF54L15 + NCS 3.0.2. We use k_uptime_get() to obtain the system uptime and perform task scheduling. Everything runs normally when the device...
I need to create a firmware to the nRF9151 SMA DK that can send a message to me (it can be via MQTT, but I prefer the nRF Cloud) containing info about the location of the...
Hi,
I'm trying to debug a Zigbee issue and for that I want to try some Zigbee samples on the nRF52840DK. But all links for Zigbee in docs.nordicsemi seem to be broken. All...
