Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Kind folks,
Situation: The product page for the Thread Topology Monitor v1.3.0 lists the following compatible dev kits (to which I've added the PCA numbers):
nRF52840...
Hi, is it posibile for use nrf21540 in the other brand BLE MCU board? some custmer maybe do not want use Nordic BLE, but want use nrf21540+other brand BLE, it is posible to...
hello!
I want to use Jlink to download code to a NRF52840 chip as MCU development board, but the number of pins and pin spacing of my Jlink are different from it. So I had...
Hi, Nordic support,
I have built success with the example "nrf5340_audio" set the gateway mode. when I run the example into my board "NRF5340 Audio DK" I get this error...
Hi,
I'm trying to use the nRF9160-DK(Ver.1.0.0) for LTE communication and GPS location information acquisition.
I found a list of LTE antennas at this URL. However, I...
We are using NRF5 SDK 17.0.2 on an NRF52840.
I am implementing a bootloader update procedure. Our updates always store the new image in external flash. The spare space in...
Hi,
I'm interested in using this AT command to upgrade my nRF52840. But I'm not quite sure what to do exactly. I'm using nRF5 V17 SDK on nRF52840. what should I provide...
Hello,
I'm thinking of increasing the transmit strength of my peripheral device using the function provided below.
sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV ,...
HI,
We are working on nRF5340DK need testing procedure for direction finding (AOA, AOD). So far we have tried to Download and install nRF connect Application for Mobile...
HI,
We are working on nRF5340DK need testing procedure for direction finding (AOA, AOD). So far we have tried to Download and install nRF connect Application for Mobile...
I recently installed the toolchain on M1 Mac using the automatic installation in the toolchain manager.
However, I noticed that the toolchain manager installs x86 variant...
Developing on ncs 2.1, using vs code and nrf connect extension to debug an application running on nrf 9160dk
I am connecting to aws iot core in a similar fashion as your...
Hello,
I have my BLE Gatt Peripheral application working and running.
I am developing a reader that reads BLE credential.
Application is complete. I flash the .hex file...
Hi
I have configured nrf52840 on my raspberry pi. I want this dongle to stop pairing to other device once connected and also most importantly stop broadcasting once it is...
Hi everyone,
currently I am trying to migrate a project from Segger Studio and SDK v1.8.0 to VS Code in combination with the SDK v2.0.0.
For the Project we are using a...
