I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi,
I tried building and debugging the sample "https_client" using the method described here . But debugging fails. Debugging stops prematurely because the source file cannot...
I need to be accurate to five decimal places.
Use nrf52840 and ses.
Test code:
Execute d=atof(mm)/60.0 result 0.70693.It's right.
But e xecute d = 0.70693+22 result...
I am trying to use SAADC.
When viewing the contents of nrfx_saadc.c in SEGGER IDE all the code is greyed-out.
I verified it is enabled in sdk_config.h:
// <e> NRFX_SAADC_ENABLED...
Hi everyone,
I am currently attending the nRF Connect Fundamental Course.
As you can see from the picture below (taken from the Course material), there must be the chance...
Hello DevZone,
I was tinkering around with the speed of the TWIM0 module in the nRF52832.
I have a cheap USB logic analyzer to help me display the waveforms and I made...
Hi,
I am using NRF52832 development board , to which i have interfaced LIS3DSH accelerometer sensor(3.3V i2c)
when i configure it for 1600 sampling rate and all the...
Hello,
I am using nRF Connect for Desktop v3.12.0 with Programmer v3.0.4 on Mac. When I program mfw_nrf9160_1.3.2.zip on the nRF9160 dev kit, it works, but when I try on...
Hello! Very quick question. The available Zigbee and ZBOSS NRF documentation repeatedly to code examples that I am unable to find. The only examples I have are at nrf/samples...
I've previously successfully done interval advertisements using a SoftDevice with Nordic's previous (non-Zephyr) sdk, but I'm having issues replicating it on Zephyr.
Our...
Hi, I am using the nRF52840 with the softdevice s140 6.1.1 with the SDK 15.3 with FreeRTOS. Sometimes after collecting data for a around a day the device sometimes crashes...
Hi,
It has been a while since I looked up on different resources to get SPI slave transaction example and I finally found on the `nrf / samples / tfm / tfm_secure_peripheral...
Hello,
I have three questions regarding FEM.
#1 According to the following URL, FEM function is supported only for nRF52 series.
Would the FEM function be available...
Hi We are working on a new product that includes NFC, When we measure the voltage level we do not reach more than 600mv. The matching was done by capacitors: using a 2uH antenna...
Dear all,
I could happily flash my firmware to my nrf52840 upon pressing reset button. When pressing the reset button the diode on the board started to beat red and via...
