Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi,
I am currently working on a project similar to this thread:
However, the thread stop updating. I followed what Einar suggested, to merge the Decawave example code...
Hi all,
I have an issue on my device. We have implement OTA update but sometimes, the nfr stucks on DFU mode after the update. Even if the update is succesfull.
We use...
Hi All.
I am checking battery autonomy with different settings in my Module (with an nRF52840 SoC inside) since, in my project, this is a critical restraint. I am feeding...
now, I need transfer data between nrf52840 (base on zephyr OS) and python app through PYSERIAL. Is it possible to use something like RTT or shell_uart to transmit/receive...
How do I switch between being SPIS/SPIM with the Zephyr library?
I am using ncs v1.9.1. I have code that works separately as a slave or master but I need to make it dynamic...
I want to use +8 dBm TX power so I added CONFIG_BT_CTLR_TX_PWR_PLUS_8 to my prj.conf, and then realised it doesn't do anything.
I then found set_tx_power() on these pages...
The problem: We are getting a hard fault immediately after jumping from the bootloader while trying to initialize the nRF USBD driver. The fault happens in nrfx_power_init...
Hi,
We are trying to integrate a remote controller functionality for smart TV and set-top box etc, using our product based on nRF52832(nRF5 SDK). I understand that we can...
I am trying to use a SPI bus with three MAX3109 chips attached to give me 6 UARTS. My overlay is defined as follows:
& spi1 {
cs-gpios = <& gpio1 13 GPIO_ACTIVE_LOW...
Hello, I'm working on a s332 application and I need to include the DFU feature in the code. I've managed to perform a DFU on s132 applications following examples like this...
I've built and able to the run the 802.15.4 RF Phy Tester but it doesn't seen to recognize any of the custom commands. Can you provide more insight into this please?
Please ignore Product Type I selected - i set it to just select that to something.
I'm planning/designing a comm box, which needs to speak to ZigBee based nodes/sensors...
Hello
I'm a beginner. I am using NRF52 series and coding in segger embedded studio. I have modified the ble_uart example and added some extra code so that I get the sensors...
Hi,
My customer occur a problem with nRF5 SDK10.0.0, the sample ble_app_hids_keyboard.
We test the sample on nRF51DK.
We connect the DK with an Android phone, and bonded...
