hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi,
Now I'm using :nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10056\s140\arm5_no_packs.
And I want to add 'Characteristic User Description Descriptor...
Hello,
I'm build my application using v1.9.1 and Visual Code. It seems I have an error saying my application size is greater than the flash size.
I CANNOT jettison any...
I have a big issue about WDT during FDA 510K preparing. I have to proof that WDT of nRF52832 is seperated structurally from main system. since nRF52832 have such a seperated...
To whom it may concern,
I have a project (using Zephyr) where I need to switch UART pins while runtime. Is there a way I can handle this? This is how I initialize pinctrl...
I am using the light_bulb sample from NCS v2.0.0 with an nRF52840 DK board. I changed prj.conf to enable Warning traces from ZBOSS:
+# Enable traces on UART_1 (P1.02) @...
Hello,
I have a question regarding the advertising and scaning mechanism implemented in Zephyr.
To be more precise, suppose the node's radio is in scan mode, and it's...
We want to create solution/project for family of boards using segger embedded studio. We want to create the solution/project in such a manner that new boards software can...
Hello,
I want to build in a reset function for handling certain error states on the 9160DK running nRF Conenct 1.6.0. In the datasheet it appears that nRESET is p0.32 and...
Hi,
I am looking for a way to count the pulses going out of a GPIO pin. If I configure that pin with the input buffer connected, how can I route that signal to a timer/counter...
Hello ,
I am a firmware engineer in Taiwan ,
I already use nRF52820 to finish one case ( cheaper alcohol/acetone BT checker.)
I used USB/ BT wireless uart / Uart send...
Hello,
I have some problems with connecting and interacting with my nRF9160. It doesn't show up in LTE Link Monitor, only got "No supported devices connected" - If i have...
Hello,
nRF52832, SEGGER Embedded Studio for ARM V4.12
We want to improve BLE transmission speed between nRF52832 and iPad mini.
Now condition and transmission speed...
I have two devices:
NRF52832_xxAA_REV2
NRF52840_xxAA_REV3
Running the Zephyr blinky sample application with the following KConfig option added:
CONFIG_NRF_APPROTECT_LOCK...
Hello,
I am trying to create a Matter device by following the steps in https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_matter_creating_accessory.html...
