I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
I notice a problem with the MCUboot Hello World example.
I followed the steps mentioned in https://www.mcuboot.com/documentation/readme-zephyr/ That is, build the MCUBoot...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0 I could build with NCS v1.9.1 but I cannot build with NCS2.0
[Build log] In file included from C:/NCS200/v2.0.0/zephyr/include...
I have an Ellisys Bluetooth Explorer 400 sniffer and am trying to sniff the ISO audio data between nrf5340 ADK boards. I enabled CONFIG_BT_LOG_SNIFFER_INFO, CONFIG_BT_DEBUG_KEYS...
Hi there. I am trying to utilize both the network core and the application core to perform two separate tasks at the same time. I have looked through some of the sample projects...
Hi, I need to setup a vendor specific class USB device driver. The driver shall present the following data endpoint:
0x84 for Bulk IN endpoint 0x03 for Bulk OUT endpoint...
SEGGER Embedded Studio for ARM can't connect to nRF52832 device. But J-Link RTT Viewer can connect to nRF52832 device. The following is log messages of J-Link RTT Viewer....
Hi there,
I am currently developing on the nRF5340DK and am doing some very processor-intensive work (@ 128MHz) on data read from the QSPI bus. I would like to set up non...
Hi, I have been trying to build an example of console usb example and then build it for thingy91_nrf9160_ns but got an error :
I have been trying this code several weeks...
Hi, with appropriate pm_static.yml and dts.overlay we managed to setup a LittleFS instance over external flash. However this broke the Settings storage subsystem the BLE stuff...
hi support team,
for our sdk17.0.2 demo hid_keyboard, i tested it and using IOS mobile to pair with our 840dk or 832dk
find out after lots of reset the keyboard device...
I am developing an application that uses nRF52840 wake on NFC, and spends most of its time in system OFF state with NFC wake enabled.
Per the nRF52840 Product Specification...
On the NRF52840 dongle am building a protocol on USB CDC ACM.
Using app_usbd_cdc_acm_read to read one byte at a time works perfectly.
However, I can seem to make app_usbd_cdc_acm_read_any...
Hi,
I am developing a wireless product in which i want to use nRF52 in ESB mode.
The product is battery powered and should be sleep mode.
What i have decided to do is...
Hi,
I have read the thread here: which implies that this config option might not work?
Does it work? I would like to build mcuboot and then always use the same binary...
