I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
In a nrf52840 project using Zephyr 3.0 following Zephyr drivers are used:
the modbus serial driver(RTU mode) which uses uart1 in interrupt mode
the lora-mac driver which...
Hi,
I'm using app_ble_uart example using nrf52810 for nrf52810 UART RX & TX pins are (P0.15 - P0.14) while configuring using i got a problem with RX transmission ,when i...
Hi,
I am working on a multiple custom models, wherein I need one model to extend the functionality of another model.
I was analyzing through nCS provided "Chat" sample...
Hello,
I'm trying to set up nRF Connect for VS Code. I followed this video for installation steps: https://youtu.be/2cv_jjqk5hg, the only difference being that my nRF Connect...
I have a VS Code project that is a Workspace Application where I've had to make some modifications to code in both zephyr and mcuboot directly. My codebase is in a git repository...
Hello!
Do you have any information on the antenna itself? Radiation pattern-diagram?
Edit: I would also like to have the specs of the antenna, eg: m ismatch loss, insertion...
I am having trouble to add the toolchain folder to the VS code setup.
The nrf connect for VS code does not pop up on the side at all to add application folder.
Tried to...
Hi guys,
I try to integrate the flash logger backend .
When I run the code I get the following error:
<error> nrf_fstorage: addr_is_within_bounds(p_fs, dest, len) check...
Greetings. I am developing a application that will run on a custom board based on the nrf52833 MCU. During development we have been using a nrf52833 development kit for testing...
Mr. Jared i do apologize for having accidentally verified&closed the issue but to answer your question we've found that the module we were using did not possess a 32khz crystal...
Hi,
I am using the code provided at https://devzone.nordicsemi.com/f/nordic-q-a/85850/example-for-extended-advertisement-receive-node
to send more than 60 bytes, but unable...
hi,
I have a problem about NCS1.9.1 NVS.
I performed `nvs_write` when ble is connected and then a reset occurs:
Whether NVS write can be performed when bluetooth is...
Hello All,
I'm new to using Nordic development kit and VSCode but I am running into an issue when I am trying to build a sample application. When I use the template to create...
I am using bt_nus_send to send data via BLE every 1ms. I've noticed that when connection is bad, this function takes a couple of milliseconds to execute, while when connection...
Hello,
I'm currently developing on the NRF9160, a sensor implementation that sends a few 100 bytes every 24hrs.
However, for demo purposes we need to send the payload...
