Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Look like a hard coded bug in API generated in build\zephyr\include\generated\syscalls\flash.h ?
-- Found BOARD.dts: zephyr/boards/arm/nrf52840dk_nrf52840/nrf52840dk_nrf52840...
Hello! I have a serial device (RN8209 power meter) which is connected by UART to a nRF52832 with 4800 Baud. I am using SDK17 nrfx UARTE to access it, but I have observed,...
We have a custom board with a uBlox Nina-B1 module. Pin 0.05 is connected to an analog switch (NX3DV2567) which powers a microphone and capacitive switch. When the pin is...
Hi everyone,
I am using nrfConnect 3.9.3, And SDK v1.7.0.
I am working on a project based on uart example.
My question is if there are some way for clean/discard all...
I'm unable to get a cloud response using the XPING command with some IoT sim cards on the nRF9160. I've been working with serial_lte_modem projects on this chipset. I've also...
I cannot find any information on how to update mcuboot over SMP when using the immutable bootloader.
I have my NRF52840 setup with the chained bootloader: b0 -> mcuboot...
Hi,
First of all thank you for your support and suggestions.
As I am planning to use nRF52840 SoC in my design, (Project: BLE based Environmental sensor). The circuit...
Hey. In production we are logging PM error events to try to determine the root cause for some unstable connection that keep showing up. We are seeing with high occurrence...
Hi,
We just received brand new nRF5340DK. By plugging in the USB and putting switch to ON I see the LEDs are blinking, but Windows doesn't detect the DK. We've tried several...
I have looked at other reports on this issue the most thorough one being
https://devzone.nordicsemi.com/f/nordic-q-a/65624/nrf52840-dk-implementing-board-button-event-handler...
I have designed some beacons based on nRF52810. The software uses the minimum functionality of the radio to transmit some packets every second and sleep.
In their sleep...
I've just ran into this issue - I was debugging while developing using a J-Link on our own board. I tried setting up UART, set the pin config to
In hindsight not the smartest...
Hey,
I want to build something like a door sensor. So my device should sleep and if the button is pressed it should wake up and send a message to the leader via thread....
