hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi Team,
I am working with a few Thingy91's. I have noticed an issue in viewing the Thingy91 output on LTE Link monitor for a few Thingy's.
The 1st Thingy connection in...
Hey, I am having trouble setting Pin 0.17 as UART TX. I have tested my code on pins 6,8,15 and 18 as UART TX and the code works. I get the required output on serial. I am...
Hi,
I have been following the webinar "Developing Matter products with nRF Connect SDK" and was successfully able to build the matter lock sample and flash to my nrf52840...
I got PPK2, connected it to Windows 10 PC and it is recognized as "nRF Connect USB CDC COM5". LEDs turn on Grenn color but immediately fade out and becomes red and stays like...
I would to like to update a nrf52833 controller via DFU from another nrf52833 controller via BLE. nrf52833 eval kit is able to connect with another nrf52833 custom controller...
Hi everyone, I am working with nrf 9160 Development Kit. I use LTE LINK MONITOR Unfortunately I am not able to connect to a LTE-NB network. I have updated the Modem Firmware...
I realize that this question will be stupid simple. I can program AVR microcontrollers with no trouble. The setup in the Segger embedded studio seems far more cumbersome....
Hello,
I have nRF52811 project which I would like to transfer to nRF52805. It is using SDK 15.3.
I saw this tutorial: https://devzone.nordicsemi.com/guides/short-range...
Good day!
Time after time I catch next assert
Assert occurs most often when I use 3+ mesh sensors in one server with periodic publication configured.
Is there any...
Now I'm using nrf52840 as a master and some other ble chips as multi peripherals.
As I know, in ble link layer data header, there is a tag: MD(More Data) , by which, every...
I installed nRF Connect Desktop. Opened Tool Manager. After sucessful installation, I tried to create ny first project by opening SES through nRF. The selections used are...
Hi,
I am using the ppk II, and I have had a number of occasions where the current displayed on the PC suddenly disappears (see attached). The voltage to the DUT seems...
Hi,
I'm testing the nRF9160 GPS performance with a GPS simulator. I set the output power to -130 dBm and test the nRF9160DK conductively. I made some small modifications...
Is there any guide or sample how to run unity tests on a target device instead of the native_posix device?
In general unity however cmock support on-device testing like...
Hello,
My config: - nRF SDK v17.1.0 - nRF SoftDevice S140 7.2.0 - FreeRTOS Kernel v10.0.0 (Amazon.com)
My project used BLE connection with custom service (based on NUS...
