Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hello
I am running this version of SES
SEGGER Embedded Studio for ARM
Release 5.34a Build 2021011401.44914
Nordic Edition
Windows x64
When I run my program in...
Hello,
I am using the pine watch hardware, to do some tests,
I configured through the overlay file, the I2C_1 to use pins 0.6, 0.7 as shown below,
&i2c1 { compatible...
Hello,
I'm playing with the timing subsystem in order to measure some execution time with higher granularity than the RTC tick on nRF52840 (using PCA10056 DK).
I'm specifically...
Hello sir,
I am using nrf58232 Dev kit board in which when my BLE goes is in advertisement board and after couple of seconds advertise APP_ADV_DURATION is expired then it...
Similar, unresolved issue can be seen here .
I just got my official nRF52840DK and setup nRF Connect on my MacBook. I'm able to build the Blinky example and flash it...
Hi,
I have the following in my code to measure throughput over the Nordic Uart Service.
It works, but I was wondering if I am measuring correctly. I took this measurement...
Hello all,
I'm working on a BLE central application based on nRF Connect SDK V1.6.1. The application connects to certain BLE peripheral devices and does a service discovery...
Hello,
I have been building an application using the CLI and I am thankful for the CLI example and how well it works. I am wondering is it possible to use the CLI but...
Hello, Im using SMP over UDP (OpenThread) and after updating to v1.6.0 in NCS, sending most commands with `mcumgr-cli` makes the device restart with:
This happens for most...
We are currently experiencing malfunction with the big chip on nRF9160dk board, which provides USB-UART and jLink functionality. After 30 minutes, to a few hours, we either...
I have nrf52832 dk. I used power down example by github
https://github.com/NordicPlayground/nrf51-powerdown-examples : system off wakeup on gpio. Upon current measuement...
Hi Nordic Engineers,
I have few queries over HFCLK 16 MHz timer.
I am using nrf52840 custom board. IDE - segger embedded studio
I have enabled HFCLK timer and able...
I'm using nRF52840 and want to send a data of 200 bytes over BLE, but while adding the characteristic, if I give maximum length above 101 it does not accept it. Can someone...
I am working on a limited release project that has multiple devices which require programming. Part of the appeal of this device is its programmability so I am going to provide...
