Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
I am researching a way to send audio from a Microphone on an APP in iOS or Android and came across the Thingy:52. Is it possible to get some guidance on the App side to transmit...
I would like to use an analog microphone to generate a voice signal, measure it by an ADC, and then transmit the sound to the host. This is the cheapest solution, but I'm...
Hello,
I'm trying DFU from here . It works successfully with nRF52833 DK Board before Appendix 1.
The question is how to combine all which it is bootloader + sd +...
Hello all, I have question about ppi.
Like code shown above, I'm using ppi.
Here, MUX_INPUT_2 and MUX_INPUT_3 are name of pin.
I'm changing their state: from low to...
Hi,
We would like to know the default state of the NRF52840’s GPIO pins - is it high, low or open? The reason for this question – we need to know these pins’ behavior/state...
Hello Guys, I want to build some project with Nordic products but ı don't have any sample code , if you have sample code for Keil let me improve myself.Actually codes can...
Hi,
As has been explained numerous times in posts on this forum and many others, mapping RSSI to a distance measurement is notoriously difficult and inaccurate. I was...
Hi
Can anyone verify that it is possible to use the nRF5340 PDK to program custom nRF53 board?
The documentation says: The nRF5340 PDK supports programming and debugging...
Hello,
we are using NRF9160 +Nrf52832 in a project. NRf52832 has to be used as HCI interface..after searching for this, i came to know that zephyr based HCI uart sample...
Hi,
I am working on Eddystone project, after I successfully tested the Buttonless DFU example, I added DFU service to Eddystone example ( nRF5_SDK_17.0.0_9d13099\examples...
I am using this MBN52832DK and find out this nRF5_SDK_17.0.0_9d13099.
Trying to import into Segger Embedded Studio but rebuild come out error.
using the nrf52832_xxaa...
Hi all,
I would like to have a semi-duplex communication link over one pin (+GND). The nRF will act as a pure slave device which responds to, and acknowledges, commands...
Hello, we understand that the Nordic framework, by default, restarts advertising on disconnect. I learned that here, thank you:
https://devzone.nordicsemi.com/f/nordic-q...
I'm currently running on nRF Connect SDK (hash: 4b012fb4882f0ddd3de9f339ebc5a3f1c3cacd4a). I'm running a connection between a nRF91+nRF52840 (as central running NUS_C) using...
I have an nRF52840 board that fails to connect to Linux over USB. The board powers on and the green LED at the lower left of the PCA10056 flashes on/off rather quickly. But...
